Typical Practice Cases; Application Of Manual Switchover Of Range Measurement Mode; Application Of Relative/Peak Value Measurement Mode - ELCART NI 2610 Manual De Usuario

ART. 09/07910-00

2.3 Typical practice cases

In the following practice cases, the user stands under a light source.
Remove the protection cover of the multi-functional light meter sensor and
Press and hold the NI2610 power key (4) for a short time to power on
the light meter. The LCD screen will illuminate about 5 seconds with the
buzzer beeping twice, and "AUTO" will appear on the middle of LCD
display. This indicates that the auto measurement mode is ON.
Press and hold the manual range switching key (9) of the NI2610 for a
short time, "MANU" will appear on the top left position of the LCD display,
indicating that the manual range switching mode has been activated. In
this mode, each time press and hold the key for a short time, the meter
the key for one second will result in the inscription "MANU" disappearing
from top left position of LCD display, replaced by "AUTO" appearing in
the middle, to indicate that the meter has switched the manual range
switching mode to the auto range switchover.
Press and hold the REL/PEAK key (8) of the NI2610 for a short time,
"REL" will appear on the top left position of the LCD interface, indicating
the activation of the relative value measurement mode.
Press and hold the key (8) for a short time again, the device will exit the
relative value measurement mode and return to the original measurement
pressing the key for one second will lead to the peak measurement mode,
press and hold the key for one second once again, "PEAK" will disappear
from the top right position of the LCD interface, and "AUTO" will appear in
the middle of LCD, and the mode will return to auto measurement mode.
Press and hold max/min value inquiry key (5) for a short time, "MAX" will
appear on top position of LCD interface, switching the device to the max/
the "MAX/MIN" key (5) for one second, "MAX/MIN" on top position of the
LCD interface will disappear, and the mode will exit.
Press and hold the data hold/zero calibration key (7) of the NI2610 for
a short time to enter the data hold mode, which will be indicated by the
and hold the key for a short time once again, "HOLD" will disappear from
the top left position of the LCD interface, and the device will exit the data
hold mode.
In any mode with sensor covered, press and hold data hold/zero calibration
key (7) for one second, "ADJ" will appear on the LCD interface, and the
device will enter the zero calibration mode: several seconds later "ADJ"
will disappear from the LCD interface, and the device will exit the data
hold mode and return to auto measurement mode.
ELCART DISTRIBUTION SPA via Michelangelo Buonarroti, 46 - 20093 Cologno Monzese (Milano) ITALY
Tel. +39 02.25117310 Fax +39 02.25117610 sito internet: www.elcart.com
La divulgazione dei dati contenuti in questa scheda è da ritenersi un servizio puramente informativo e non costituisce alcun vincolo da parte della Elcart in merito a prestazioni ed utilizzo del prodotto.
The divulgation of data contained on this technical sheet are exclusively for informational reasons and establish no link on behalf of Elcart regard to thr performances and the usa of the product.
La divulgacion de los datos contenidos en esta ficha son un servicio unicamente informativo y no constituyen ningun vinculo de parte de Elcart respecto a las prestaciones y uso del producto.
ELCART
Manuale di istruzioni/Scheda tecnica
Figura 2-1

3.1 Application of manual switchover of range measurement mode

Press and hold the RAN key (range manual switchover key) for a short
time, "MANU" will appear on the top left position of the LCD interface,
and the meter will enter the manual switchover measurement mode (as
When entering manual switchover of range function, press RAN key for
Press and hold RAN key for one second, "MANU" on the top left position
of the LCD interface will disappear, and "AUTO" will appear in middle of
LCD interface, and manual range switchover function will exit and the
device will return to auto range switchover mode
Tips
1. Only in peak value measurement mode, relative value measurement
mode and max/min value inquiry mode, it will be effective to press RAN
key for a short time.
2. In relative value measurement mode and max/min value inquiry mode,
press and hold the key for one second, it will return to auto switchover
of range.
3. In peak value measurement mode, data hold mode and zero calibration
modes, it will be effective to press and hold RAN key for a long time.
4. In this mode, when measurement value exceeds present range, "OL"
will appear on LCD interface to indicate over-range, and the user should
switch over the measurement range at this time.

3.2 Application of relative/peak value measurement mode

Press and hold REL/PEAK key for a short time (composite key for relative/
peak value measurement), "REL" will appear on the top left position of
Press and hold REL/PEAK key for a short time again, "REL" on the top
left position of the LCD interface will disappear, and the device will exit the
relative value measurement mode and return to original measurement
Press and hold "REL/PEAK" key for one second, the device will enter the
peak value measurement mode, "PEAK"LCD will appear on the top right
position of the LCD interface, and at the same time, "MENU" will appear
Press and hold the key once again for one second, "PEAK" on top
right position of LCD interface will disappear, and "AUTO" will appear
on the middle of LCD interface, and the device will exit the peak value
measurement mode and return to auto measurement mode (as shown
in 3-1-2C).
Tip
1. Only in auto measurement mode, peak value measurement mode, max/
min value inquiry mode and data hold mode, it will be effective to press
and hold REL/PEAK key for a short time.
2. In non-zero calibration mode, press and hold "REL/PEAK" for one
second, the device will enter the peak value measurement mode.
PAGINA 8 DI 15
e-mail: [email protected]