Tabla de contenido
Idiomas disponibles
Idiomas disponibles
be fixed there is a suitable type of bolts and screws; therefore,
buy it according to necessity. If necessary, use washers to
increase the surface area.
SCREWING OPERATION
Place the screw on the panel to be fixed and with a hammer tap
it lightly in a perpendicular position.
For some materials it is necessary to make a pre-hole in order
to facilitate the screwing and to prevent the panel breaking
(especially with wood and plastic).
Grip the screwdriver firmly with one hand and insert the tip
of the bit in the screw head. Lightly press on the screw and
run the screwdriver, activating the switch gradually so as to
modulate the rotating speed and, consequently, the speed of
screw penetration.
At the end of this operation, which usually lasts a few seconds,
remove the screwdriver and turn it off by releasing the switch.
The speed rotation may be modulated electronically from a null
value up to a max value through smaller or greater pressure on
the switch. By means of the grain roller (pos.20, if fitted) it is
possible to mechanically pre-set the stroke of the switch and
therefore the max speed allowed. The screwing speed depends
on the following factors: panel material, screw size, thread,
presence or absence of a pre-hole, etc.
After the screwing phase, the internal rotation joint will be
uncoupled, the electrical tool will become very noisy and will
vibrate; now, remove the screwdriver and turn it off.
Continuing to screw may cause: the breakage of the insert,
damage to the screw head, and failure of the electrical tool (in
this case not covered by the warranty). In this case, unscrew the
screw, perform a pre-hole with a driller and re-screw modifying
the adjustments.
Do not force screws that do not screw!
MAINTENANCE
! IMPORTANT! Before any checks or adjustments take the
battery out of the tool and unplug the battery charger from
the mains.
! IMPORTANT! Do not tamper or attempt to repair the
electrical tool.
The working life and costs also depend on constant and meti-
culous maintenance.
Take good care of your electrical tool and clean it regularly. In
this way its efficiency will be ensured and its lifespan extended.
- Remove dust and machining residuals with a brush with soft
bristles.
- Do not wet or spray water over the electrical tool - risk of
internal infiltrations.
- Do not use any inflammables, detergents or solvents.
- The plastic parts can easily be damaged by chemical agents.
- Do not use compressed air for cleaning: Risk of material
ejection!
- Be careful when cleaning the switch, motor fan slots, chuck,
battery and battery charger.
The tool does not require any special maintenance inasmuch as
it is lubricated with permanent grease inside. Any internal servi-
cing must only be performed by an authorised service centre.
CHUCK REPLACEMENT (fig.D)
1) Open the chuck jaws completely.
2) Insert a screwdriver in the front part of the chuck until reaching
the safety screw.
3) Loosen the safety screw by turning it clockwise (left thread).
- 16 -
4) Position the friction on high torque (high number).
5) Now unlock the chuck with a sharp hit in an anti-clockwise
direction and unscrew it manually.
To assemble the new chuck, follow the previous operations in
the reverse order.
Carry out a trial run.
STORAGE
Clean the tool and all its accessories thoroughly (see Maintenan-
ce section). Protect the unpainted parts with protective oil and
use the original packaging or case (where fitted) to protect it.
Keep the machine out of reach of children, in a stable and safe
position. The place must be dry, free from dust, temperate and
protected from direct sunlight.
Keep children and unauthorised personnel out of the storage
room.
DISPOSAL
In order to protect the environment, proceed according to the
local laws in force. Contact the relevant authorities for more
information.
When the machine is not longer useable or repairable, deliver
the machine and packaging to a recycling centre. Take out the
batteries (where fitted) and dispose of them separately.
Electric and electronic waste may contain substances that
are dangerous for the environment and for human health. For this
reason they must never be disposed of together with domestic
waste, but collected separately in specific collection centres or
returned to the retailer when similar new equipment has been
purchased. The illegal disposal of such equipment may result
in prosecution to the full extent of the law.
Battery disposal: The batteries included in the equipment
can be disposed of along with it.
Do not throw the used batteries on the fire and do not dispose
of them in the environment, but take them to special disposal
centres. Do not dispose of them with domestic waste.
Tabla de contenido
