Makita GV7000 Manual De Instrucciones página 3

ENGLISH
(Original instructions)
1 Switch trigger
2 Lock button
3 Speed adjusting dial
4 Cover
5 Side grip
SPECIFICATIONS
Model
Abrasive disc diameter ................................................................. 180 mm
Spindle thread ............................................................................. M14
No load speed (n ) / Rated speed (n)........................................... 4,700 (min
0
Overall length ............................................................................... 210 mm
Net weight..................................................................................... 2.1 kg
Safety class ..................................................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for the sanding of large surface of
wood, plastic and metal materials as well as painted sur-
faces.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
DISC SANDER SAFETY WARNINGS
Safety Warnings Common for Sanding Operation:
1. This power tool is intended to function as a
sander. Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
2. Operations such as grinding, wire brushing, pol-
ishing or cutting-off are not recommended to be
performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
3. Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
Explanation of general view
6 Lock nut
7 Abrasive disc
8 Rubber pad
9 Spindle
10 Lock nut wrench
4.
5.
ENE052-1
6.
ENF002-2
7.
GEA010-1
GEB036-5
8.
9.
11 Wrench
12 Limit mark
13 Brush holder cap
14 Screwdriver
GV7000
-1
)
/II
The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
Threaded mounting of accessories must match
the tool spindle thread.
mounted by flanges, the arbour hole of the
accessory must fit the locating diameter of the
flange. Accessories that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
Do not use a damaged accessory. Before each
use inspect the accessory such as backing pad
for cracks, tear or excess wear. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After inspect-
ing and installing an accessory, position your-
self and bystanders away from the plane of the
rotating accessory and run the power tool at
maximum no-load speed for one minute. Dam-
aged accessories will normally break apart during
this test time.
Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
mask, hearing protectors, gloves and workshop
apron capable of stopping small workpiece frag-
ments. The eye protection must be capable of stop-
ping flying debris generated by various operations.
The dust mask or respirator must be capable of fil-
trating particles generated by your operation. Pro-
longed exposure to high intensity noise may cause
hearing loss.
Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of work-
piece or of a broken accessory may fly away and
cause injury beyond immediate area of operation.
GV7000C
180 mm
M14
-1
4,700 (min )
210 mm
2.1 kg
/II
For accessories
3