100% Armega Manual De Instrucciones página 5

EN
GOGGLE CARE
•Clean the lenses with mild ph. 5.5 soap and water.
•Blot the lens with your goggle bag or a soft cloth to remove excess moisture, or
allow to air dry.
•Avoid cleaning or drying the lens with any paper products as it will damage the
lens and/or coatings.
•If the lens is scratched, please contact your authorized 100%® dealer to
purchase replacement parts.
•For your safety, trust only genuine 100%® CE® certified replacement lenses,
parts and accessories.
•Do not place your goggles face down.
•Always store your goggles in the supplied bag after use or during transport.
•Always store your goggles in a cool, dry place away from direct sunlight
and/or heat.
•Do not expose your goggles to extreme heat conditions
•Do not expose your goggles to strong detergents or harsh chemicals.
•Do not bend your goggles unnecessarily.
•Inspect your goggles regularly for damage.
•If there's damage; the lens and/or goggle should be replaced immediately.
Scratched lenses should be replaced immediately.
Questions? Please contact 100%® customer service at [email protected]
LIMITED WARRANTY
100%® provides a one-year warranty against manufacturing defect from the
date of purchase. During the term of this warranty, 100%® will replace any
current style which is deemed by 100%® to possess a manufacturing defect.
Scratched lenses or other wear and tear as a result of normal use are not covered
by this warranty. For warranty or replacement service, please contact us at
[email protected]
INTENDED USE
This is not a safety goggle. This goggle is intended for motorsports use only ex-
cept official races and competitions. It is for protection from wind, solar radiation,
and impacts from water and mud. This goggle is resistant to scratches in the
event of contact with small metallic partials at a rate of 60 m/s.
This goggle for motorcycle and moped users is manufactured in conformity with
the basic requirement established by the Regulation (EU) 2016/425 on personal
protective equipment. The EU Declaration of Conformity can be found at: http://
www.ride100percent.com/declarations/
On the goggle is reported the following marking:
•Normative Number: EN 1938:2010
•Brand: 100%®
PRODUCT CERTIFIED BY
CERTOTTICA Scarl (NBN ID – 0530)
ZI VILLANOVA, 32013
LONGARONE BL, ITALY
FILTER CATEGORY
Filter Category % Visible Light Transmission Warning
0
1
2
LENS REPLACEMENT
REMOVING LENS:
While grasping the goggle with one hand, use your other hand to grab onto the
1
locking latch and rotate towards the lens to disengage. Repeat until both sides
are fully unlocked.
Grab onto the lens edge and peel up and away from the nose. Do not rotate or
2
pull off the lens in a downward motion toward the nose.
INSERTING LENS:
While grasping the goggle and keeping the lens parallel to the goggle frame,
1
press down the nose section until lens snaps into place.
2 Verify that the lens is fully seated around the perimeter of the goggle frame.
With one hand apply pressure near lens edge and with the other hand, push the
3
latch to engage the lock. Repeat until both sides are full locked.
TRIPLE POST TEAR-OFF SYSTEM INSTALLATION
*Laminated tear-offs with a perimeter seal must have the backing removed prior to
application and firmly applied.
1. Begin with a single tear-off or stack of laminated tear-offs and place hole (A) onto
post (1)
2. Place hole (B) onto post (2)
3. Place hole (C) onto post (3)
4. Fold hole (D) over post (3)
Repeat steps until tear-off folds match Figure 1
80-100
43-80
18-43
Lenses with luminous transmittance less
than 75% are not suitable for night or
twilight use!
Not suitable for night driving or twilight
conditions.
Fig 1.