Part Names And Functions; Auto Power-Off Function - Vox MV50 High Gain Boutique Compact Manual De Usuario

English
Introduction
Thank you for purchasing the VOX MV50 High Gain/MV50 Boutique
guitar amplifier. To help you get the most out of your new instrument,
please read this manual carefully.
About Nutube
Nutube is a new vacuum tube developed by KORG INC. and Noritake
Itron Corporation and that utilizes technology from vacuum fluorescent
displays.
As with conventional vacuum tubes, the Nutube is constructed with
an anode, grid and filament, and operates as a complete triode tube.
Furthermore, it generates the response and same rich harmonic
characteristics of conventional vacuum tubes.

Part Names and Functions

4
1 2 3
1. GAIN knob: Controls the pre amp gain.
2. TONE knob: Controls the tonal color.
3. VOLUME knob: Controls the volume levels for the SPEAKER
OUTPUT jack and PHONES / LINE jack.
4. VU meter: Shows the output level of the amplifier.
5. INPUT jack: Plug your guitar in here, ensuring you use a shielded
guitar cable.
6. PHONES / LINE jack: Use this jack if you want to output directly to
a mixer or a recording device, or when you want to use headphones.
Output level is adjusted with the VOLUME knob.
Both the IMPEDANCE and EQ switches do not affect the output
from this jack.
7. ECO switch: The Auto Power-Off function can be disabled by
moving the switch to the OFF position.
8. Power switch: When the switch is moved to the ON position, the
amp turns on.
9. DC 19 V jack: Connect the included AC adapter here.
10. EQ switch: You can change the tonal character of the sound by this
switch.
Switch position FLAT
Cabinet to be used Large cabinet
Sound Flat
11. MID CTRL/IMPEDANCE switch: You can change these parameters
of the amplifier.
MV50 High Gain
A control switch to boost/cut the amp mid range.
Switch position - (MINUS)
Amp mid range Cut
MV50 Boutique
An impedance switch to optimize the sound character.
Switch position 4
Impedance 4 ohm
(The figure shows MV50 Boutique)
7 8 9 10 11
6
DEEP
Small cabinet
Thick and warm
NORM + (PLUS)
Normal Boost
8 16
8 ohm 16 ohm
12. SPEAKER OUTPUT jack: Connect the speaker cable to this jack.
The minimum speaker's impedance is 4ohms, and you will get
approx. 50W output with 4ohms, 25W with 8ohms, and 12.5W with
16ohms load.
Do not connect a load less than 4ohms.
The MV50 has a built-in protection system that prevents damage
should unusual circumstances occur. If the sound cuts out for
a few seconds, don't worry, this is the MV50 protecting itself
and your speakers. If you find this happens, simply reduce the
volume on the MV50 slightly. (This protection only occurs with
16Ω speakers. 8Ω and 4Ω speakers are unaffected.)
This is BTL (Bridge-Tied-Load) output. This means both tip and
sleeve is the signal line, and sleeve is not grounded. Only use
this jack for connecting speakers to MV50. Connecting anything
else may result in damages to MV50.
Setup
1. Turn the VOLUME knob on the amp to the minimum position.
12
2. Connect the supplied AC adapter to the power cord. Insert the DC
plug end into the DC 19 V jack. Next, plug the power cord into an
AC outlet.
Be sure you're using an AC outlet of the correct voltage for your unit.
Use only the supplied AC adapter. Using any other AC adapter
may cause malfunctions.
3. Plug the cable that's connected to your guitar into the INPUT jack.
4. Plug the speaker cable that's connected to the speaker cabinet into
SPEAKER OUTPUT jack.
SPEAKER OUTPUT jack may not be used if not needed. This
won't harm the amp.
5. Turn the amp on, and slowly raise the VOLUME knob to adjust
the volume.

Auto power-off function

The amp has an auto power-off function. With this function, the amp
is automatically turned off if there is no output for approximately 15
minutes. Switching the ECO on enables the auto power-off function,
whereas switching the ECO off disables the function.
When the amp is turned off, it is not automatically turned back on. After
the amp is turned off, turn it on again or turn this switch off.
When the output level is extremely low or there is very little change
in the sound, the auto-power off function may be activated. In
addition, depending on the setting and environment, the amp may
interpret noise as input, even if the guitar is not being played.
Specifications
Input/Output Jacks: INPUT Jack × 1, SPEAKER OUTPUT Jack × 1
Vacuum tube:
Output Power:
Power supply:
Current Consumption:
Dimensions (W× D×H):
Weight:
Included items:
* Appearance and specifications of this product are subject to change without
.
notice
- 2 -
(6.3 mm monaural phone jack, unbalanced)
PHONES / LINE Jack × 1
(6.3 mm stereo phone jack)
Nutube 6P1
Maximum approx 50 W RMS@4 ohms,
25 W RMS@8 ohms, 12.5 W RMS@16 ohms
AC adapter (DC 19 V
3.42 A
135 × 75 × 100 mm/5.31 × 2.95 × 3.94 inches
540 g/1.19 lbs.
AC adapter, Power cord, Owner's Manual
)