Important Safety Instructions - Makita AN760 Manual De Instrucciones

ENGLISH
(Original instructions)
1 Pneumatic tool oil
2 Adjuster
3 Door
4 Latch lever
5 Magazine cap
6 Coil support plate
SPECIFICATIONS
Model
Air pressure
Nail length
Nail capacity
Min. hose diameter
Pneumatic tool oil
Dimensions (L x H x W)
Net weight
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for the making pallets and wooden
boxes.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: WHEN USING
SAFETY PRECAUTIONS
FOLLOWED TO REDUCE THE RISK OF PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
• For personal safety and proper operation and mainte-
nance of the tool, read this instruction manual before
using the tool.
• Always wear safety glasses to protect your eyes from
dust or nail injury.
WARNING:
It is an employer's responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
• Wear hearing protection to protect your ears against
exhaust noise and head protection. Also wear light but
not loose clothing. Sleeves should be buttoned or rolled
up. No necktie should be worn.
Explanation of general view
7 Graduation
8 Feed Claw
9 Air fitting
10 Air socket
11 Trigger
12 Hammer
ENE075-1
GEA010-1
ENB090-4
THIS TOOL, BASIC
SHOULD ALWAYS BE
13 Small rod
14 Drain cock
15 Air filter
16 Oiler
17 Pneumatic oil
AN760
0.49 – 0.83 MPa (4.9 – 8.3 bar)
45 mm – 75 mm
200 – 300 pcs.
6.5 mm
Turbine oil
312 mm x 331 mm x 131 mm
3.2 kg
• Rushing the job or forcing the tool is dangerous. Han-
dle the tool carefully. Do not operate when under the
influence of alcohol, drugs or the like.
• General Tool Handling Guidelines:
1. Always assume that the tool contains fasteners.
2. Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
3. Do not activate the tool unless the tool is placed
firmly against the workpiece.
4. Respect the tool as a working implement.
5. No horseplay.
6. Do not hold or carry the tool with a finger on the
trigger.
7. Do not load the tool with fasteners when any one of
the operating controls is activated.
8. Do not operate the tool with any power source other
than that specified in the tool operating/safety
instructions.
• An improperly functioning tool must not be used.
• Sparks sometimes fly when the tool is used. Do not use
the tool near volatile, flammable materials such as gas-
oline, thinner, paint, gas, adhesives, etc.; they will
ignite and explode, causing serious injury.
• The area should be sufficiently illuminated to assure
safe operations. The area should be clear and litter-
free. Be especially careful to maintain good footing and
balance.
• Only those involved in the work should be in the vicin-
ity. Children especially must be kept away at all times.
• There may be local regulations concerning noise which
must be complied with by keeping noise levels within
prescribed limits. In certain cases, shutters should be
used to contain noise.
• Do not play with the contact element: it prevents acci-
dental discharge, so it must be kept on and not
removed. Securing the trigger in the ON position is also
very dangerous. Never attempt to fasten the trigger. Do
not operate a tool if any portion of the tool operating
controls is inoperable, disconnected, altered, or not
working properly.
7