Assembly; Wp 10H; Wp 12H; Wp 20H - HOLZMANN MASCHINEN WP 10H Manual De Instrucciones

11.2 Assembly

11.2.1 WP 10H

The WP 10H is generally delivered pre-assembled. For dismounted parts which has to be
mounted, use the explosion drawing of the WP 10H if necessary.

11.2.2 WP 12H

The WP 12H is also delivered pre-assembled. Numbers () refer to the exploded view of the WP
12H. The following parts are to be installed.
 Attach one base section (20) to left post and lower cross member (25) using bolts (24),
washers (21), lock washers (22) and nuts (23), then attach another to right post and the
lower cross member.
 Put the press frame in an upright position, attach the two upper cross beams (32) to left
and right posts (19) using bolts (12), washers (15), lock washers (14) and nuts (13).
 Put the upper plate (6) onto the upper crossbeam, insert the bolt (5) into the hole in the
upper plate and insert the ram into the hole in the upper plate.
 Screw the upper round nut (7) onto the ram until end, then put the under plate (8) onto
the ram through the bolt (5), secure the upper plate and under plate by tightening the
washers (9) and nuts (10) to the bolt (5).
 Insert bed frame pin (18) into the holes in the posts, then insert the press bed frame (17)
into press frame and onto bed frame pin.
 Attach the setting plate (26) to the right post using bolts (24), washers (21), lock washers
(22) and nuts (23), then secure the pump assemblies using the bolt (27) and washers
(28), and then insert the handle (30) to the handle bracket.
 Connect the hydraulic hose fitting (33) to the connection nut (34) and assemble the
pressure gauge (1) to the pressure gauge connection nut (35) which is on the top of ram
(3).
 Tighten all bolts and screws.

11.2.3 WP 20H

The WP 20H is also delivered pre-assembled. Numbers () refer to the exploded view of the WP
20H. The following parts are to be installed.
 Attach one base section (21) to left post and lower cross member (26) using bolts (25),
washers (22), lock washers (23) and nuts (24), then attach another to right post and the
lower cross member.
 Put the press frame in an upright position, attach one upper cross beam (10) to left and
right posts (20) using bolts (9), washers (13), lock washers (12) and nuts (11).
 Put another upper crossbeam into position and insert the under plate (7) to the two upper
cross beams at the same time, then secure this cross beam to the posts using bolts (9),
washers (13), lock washers (12) and nuts (11).
 Screw the upper round nut (6) onto the ram (3), insert the ram into the hole in the under
plate (7), then screw the under round nut (8) onto the ram and attach the serrated saddle
(5) to the ram.
 Join the two press bed frame (18) together by inserting the four bolts (27) through the
bushings (28) and the holes in the bed frames, then secure the four bolts by tighten the
washer (14), lock washer (15) and nut (16) on it.
 Insert bed frame pin (19) into the holes in the posts, then insert the joined press bed
frame (18) into press frame and onto bed frame pin.
 Attach the setting plate (31) to the right post using bolts (25), washers (22), lock washers
(23) and nuts (24), then secure the pump assemblies using the screws (29) and washers
(30), and then insert the handle to the handle bracket.
 Connect the hydraulic hose fitting (36) to the connection nut (37) and assemble the
pressure gauge (1) to the pressure gauge connection nut (38) which is on the top of ram
(3).
 Tighten all bolts and screws.
HOLZMANN MASCHINEN GmbH www.holzmann-maschinen.at
ASSEMBLY
16
WP 10H/WP 12H/WP 20H