Idiomas disponibles
Idiomas disponibles
if you experience
TROUBLESHOOTING
Possible causes
First try the solutions
suggested
here
for assistance
and to possibly
avoid
a service
call.
!
Solution
Washer
not draining/
Check
plumbing
for correct
drain
hose
Check drain
hose for proper
installation.
Use drain
hose form
spinning,
loads are
installation.
Drain hose extends
into
and securely
attach
to drainpipe
or tub. Do not tape
over drain
still wet or spin light
standpipe
farther
than 4.5"
(114 ram).
opening.
Lower drain
hose if the end is higher
than 96" (2.4 m)
remains on (indicating
above
the floor.
Remove any clogs from drain
hose.
that the washer
was
Too much detergent
causing
suds to
Always
measure
and follow
detergent
directions
for your load.
unable
to pump out
slow or stop draining
and spinning.
To remove extra
suds, select Rinse/Spin.
Do not add detergent.
water
within
10 minutes)
(cont.)
Dry spots on load
High speed
spins extract
more
The high spin speeds
combined
with air flow during
the final spin
after
cycle
moisture
than your previous
washer,
can cause items near the top of the load to develop
dry spots
during
the final spin. This is normal.
Washer
may be tightly
packed.
Use Bulky/Bedding
or Deep Wash cycle for higher
water
fill. See
"Cycle Guide"
to match
your load with the best cycle.
Added
extra garments
to the load
Add only 1 or 2 additional
garments
after
washer
has started.
after
the sensing/fill
phase.
Check for proper
water
supply.
Incorrect
or wrong
wash or rinse
temperatures
Energy saving
controlled
wash temperatures.
Load not rinsed
Check for proper
water
supply.
Not using HE detergent
or using too
much HE detergent.
Washer
not loaded
as recommended.
Sand, pet hair, lint,
Heavy sand, pet hair, lint, and
etc. on load after
detergent
or bleach
residues
may
washing
require additional
rinsing.
Load is tangling
Washer
not loaded
as recommended.
Make
sure hot and cold inlet hoses are not reversed.
Both hoses must be attached
to both washer
and faucet,
and
have both hot and cold water
flowing
to inlet valve.
Check that inlet valve
screens are not clogged.
Remove any kinks in hoses.
ENERGY
STAR<_> q ualified
washers
use cooler
wash and rinse water
temperatures
than traditional
top-load
washers.
This includes
cooler
hot and warm
washes.
Make
sure hot and cold inlet hoses are not reversed.
Both hoses must be attached
and have water
flowing
to the
inlet valve.
Both hot and cold water
faucets
must be on.
Inlet valve
screens on washer
may be clogged.
Remove any kinks in the inlet hose.
The suds from too much detergent
can keep washer
from
operating
correctly.
Always
measure
detergent
and follow
detergent
directions
based on load size and soil level.
The washer
is less efficient
at rinsing when load is tightly
packed.
Load garments
in loose heaps evenly around
the basket
wall.
Load with dry items only.
Use cycle designed
for the fabrics
being washed.
Add only 1 or 2 additional
garments
after
washer
has started.
Use Bulky/Bedding
or Deep Wash cycle for higher
water
fill. See
"Cycle Guide"
to match
your load with the best cycle.
Add Two Rinses to the selected
cycle.
See "Using Your Washer"
section.
Select a cycle with a slower wash action
and spin speed;
however,
items will be wetter
than those using a higher
speed spin. Use
Bulky!Bedding
or Deep Wash cycle for higher
water
fill. See the
"Cycle Guide"
to match
your load with the best cycle.
Load garments
in loose heaps evenly around
the basket
wall.
Reduce tangling
by mixing
types of load
items. Use the
recommended
cycle for the type of garments
being
washed.
14
