Craftsman WEEDWACKER 316.795861 Manual Del Operador página 7

Recortador/ cortamalezas a gasolina
Ocultar thumbs Ver también para WEEDWACKER 316.795861:
Idiomas disponibles

Idiomas disponibles

OiL AND FUEL MiXiNG iNSTRUCTiONS
Old and/or improperly mixed fuel are the main reasons for the unit not
running properly. Be sure to use fresh, clean unleaded fuel. Follow the
instructions
carefully for the proper fuel/oil mixture.
Definition
of Blended
Fuels
_[_
WARNING:
It has been proven that fuel containing greater than I
15% ethanol will likely damage this engine and void the warranty, j
Today's fuels are often a blend of gasoline and oxygenates such as ethanol,
methanol, or MTBE (ether). Alcohol-blended
fuel absorbs water. As little as 1%
water in the fuel can make fuel and oil separate. It forms acids when stored.
When using alcohol-blended
fuel, use fresh fuel (less than 30 days old).
Using Blended
Fuels
If choosing to use a blended fuel, or its use is unavoidable, follow
recommended
precautions:
• Always use the fresh fuel mix explained in the operator's
manual
Always agitate the fuel mix before fueling the unit
Drain the tank and run the engine dry before storing the unit
Using Fuel Additives
_
CAUTION:
For proper engine operation
and maximum
I
reliability, pay strict attention to the oil and fuel mixing instructions
onthe2-cyceo
contaner.
Usng
mproperymxedfue
can
|
severely damage the engine.
]
The bottle of 2-cycle oil that came with the unit contains a fuel additive that
will help inhibit corrosion and minimize the formation of gum deposits.
Always use a good 2-cycle oil designed for air-cooled engines along with a
fuel additive, such as STA-BIL® Gas Stabilizer or an equivalent. Add 0.8 oz.
(23 ml) of fuel additive per gallon of fuel according to the instructions
on the
container. NEVER add fuel additives directly to the unit's fuel tank.
Thoroughly mix the proper ratio of
2-cycle engine oil with unleaded
gasoline in a separate fuel can. Use
a 40:1 fuel/oil ratio. Do not mix
them directly in the engine fuel tank.
See the table below for specific gas
and oil mixing ratios.
NOTE:
One gallon (3.8 liters) of
unleaded gasoline mixed
with one 3.2 oz. (95 ml)
bottle of 2-cycle oil makes
a 40:1 fuel/oil ratio.
NOTE:
Dispose of the old fuel/oil
mix in accordance to
Federal, State and Local
regulations.
UNLEADED GAS
1 GALLON US
(3.8 LITERS)
1 LITER
2 CYCLE OiL
3.2 FL. OZ.
(e5 ml)
25 ml
MiXiNG RATIO - 40:1
_
WARNING:
Gasoline is extremely flammable.
Ignited vapors
may explode. Always stop the engine and allow it to cool before
filling the fuel tank. Do not smoke while filling the tank. Keep
sparks and open flames at a distance from the area.
FUELING THE UNiT
--
i
_L_
WARNING:
Remove fuel cap slowly to avoid injury from fuel
spray. Never operate the unit without the fuel cap securely in place.
_
WARNING:
Add fuel in a clean, well ventilated outdoor area. Wipe
up any spilled fuel immediately. Avoid creating a source of ignition for I
spilt fuel. Do not start the engine until fuel vapors dissipate.
]
1.
Turn unit on its side, with the fuel cap facing up, and remove the fuel cap.
2.
Place the gas container's
spout into the fill hole on the fuel tank and fill
the tank.
NOTE:
Do not overfill the tank.
3.
Wipe up any gasoline that may have spilled.
4.
Reinstall the fuel cap.
5.
Move the unit at least 30 ft. (9.1 m) from the fueling source and site
before starting the engine.
WARNING:
Operate this unit only in a well-ventilated
outdoor
area. Carbon monoxide exhaust fumes can be lethal in a confined
area.
WARN_NG:
Avoid accidental
starting. Make sure to be in the
starting position when pulling the starter rope (Fig. 16). To avoid
serious injury, the operator and unit must be in a stable position
while starting.
STARTING
INSTRUCTIONS
off (o)
1.
Mix gas with oil. See Oil and
"__
Fuel Mixing Instructions.
on (I)__
2.
Fill the fuel tank with the
fuel/oil mixture.
NOTE:
There is no need to turn
the unit on. The On/Off
Control is in the ON ( I )
position at all times
Throttle
(Fig. 13).
Control
Fig. 13
3.
Fully press and release the
primer bulb 10 times, slowly.
Some amount of fuel should
be visible in the primer bulb
and fuel lines (Fig. 14). If fuel
can not be seen in the bulb,
press and release the bulb as
many times as it takes until
fuel can be seen in it.
4.
Flip the choke lever clockwise
until it clicks (Fig. 15).
5.
Crouch in the starting position
(Fig. 16). Do not squeeze the
throttle. Pull the starter rope
with a controlled motion until
the unit starts.
6.
Wait and allow the unit to idle for
5 - 10 seconds. If the unit stops
running during this time, squeeze
the throttle control and pull the
starter rope in a controlled
motion until the unit starts.
7.
Squeeze and hold the throttle
control for 30 to 60 seconds to
allow the unit to warm up.
NOTE:
The unit uses the
INCREDI-PULL
TM
starting
system, which significantly
reduces the effort required
to start the engine. The
starter rope must be
pulled out far enough to
hear the engine attempt to
start. There is no need to
pull the rope briskly-- there
is no harsh resistance
when pulling. Be aware
that this starting method is
vastly different from (and
much easier than) what
you may be used to.
The engine does not start,
go back to step 3.
If the unit is hot and fails
Fig. 14
Choke Lever
Fig. 15
IF...
Throttle Control
Fig. 16
NOTE:
Starting
Position
to start within 3 pulls of the starter rope, squeeze the throttle control
and pull the starter rope until the unit starts.
STOPPING
INSTRUCTIONS
1.
Release the throttle control and allow the engine to cool down by idling.
2.
Press and hold the On/Off Control in the OFF (O) position until the
engine comes to a complete
stop (Fig. 13).
7
loading