Idiomas disponibles
Idiomas disponibles
8. Switch on the appliance. The appliance starts with the
heating process. The heating plate becomes hot. Wait
until all the control lamps light up.
9. Use the control on the top of the milk tank to set whether
you want milk foam with a low consistency ( ) or a high
consistency ( ).
10. Depending on which filter insert you have inserted,
press button (2) for a small caffè latte or button (5) for a
large caffè latte.
11. Wait until no more coffee and milk is dispensed. Several
beeps sound and all control lamps light up. Remove
the cup.
- Remove the filter holder after each preparation. This
prolongs the life of the rubber seal in the brew head.
- For reasons of hygiene, clean the milk tank and its
parts after each use! See chapter "Cleaning". In ad-
dition, dried milk can clog the pipes and, in extreme
cases, cause the appliance to become defective if it
is not cleaned after each use.
Frothing Milk
1. Make sure that there is enough milk in the milk tank.
(See section "Removing and Filling the Milk Tank".)
2. Swivel the milk nozzle outwards with the adjustment
lever on the milk tank.
3. Place a cup under the brewing head and make sure that
the milk nozzle extends into the cup. If necessary, adjust
the length of the milk nozzle as previously described.
4. Switch on the appliance. The appliance starts with the
heating process. The heating plate becomes hot. Wait
until all the control lamps light up.
5. To activate the milk frothing function, press and hold the
FROTH / LATTE button for 3 seconds. A beep sounds
and the control lamp on the button flashes, while the
other control lamps go out. After a short heating phase,
milk flows out of the milk nozzle.
6. When no more milk flows out, several beeps sound and
all indicator lights light up. Remove the cup.
- For reasons of hygiene, clean the milk tank and its
parts after each use! See chapter "Cleaning". In ad-
dition, dried milk can clog the pipes and, in extreme
cases, cause the appliance to become defective if it
is not cleaned after each use.
WARNING:
• Always pull the mains plug out of the socket before cleaning
and wait until the appliance has cooled down.
PC-ES-KA1266_IM_01.2024
Use of Nespresso Compatible Capsules
The appliance can also be used with Nespresso compatible
capsules.
1. Fill the water tank with sufficient water. Close the water
tank lid.
2. If you are using a capsule that also requires milk for
preparation, also fill the milk tank with sufficient milk.
(See section "Removing and Filling the Milk Tank".)
3. Insert a Nespresso compatible capsule into the capsule
adapter. Press the capsule into the adapter with light
pressure. The metal tips at the bottom of the adapter
pierce the capsule.
4. Insert the adapter for the capsules into the filter holder
(12).
5. Fit the filter holder to the brew head. Make sure that the
filter holder is firmly seated in the brew head.
6. Place a cup under the brewing head.
7. Switch on the appliance. The appliance starts with the
heating process. The heating plate becomes hot. Wait
until all the control lamps light up.
8. Depending on the capsule inserted, press the corre-
sponding button. The hot water is pressed through the
filter.
9. When the appropriate amount of coffee has been
dispensed, you will hear several beeps. Remove the
cup(s).
- Remove the filter holder after each preparation. This
prolongs the life of the rubber seal in the brew head.
10. Detach the filter holder from the brew head.
11. To prepare another cup, the capsule must be replaced
with a new capsule:
WARNING: Risk of Burns!
The metal parts on the filter holder and the filter insert
are hot.
Before you can change the capsule, you must cool the
adapter for Nespresso compatible capsules under cold
water.
12. To prepare the next cup(s), proceed as described above.
- The coffee temperature of the first cup prepared and
the following cup(s) may be different.
Cleaning
19
03.01.24
