Idiomas disponibles
Idiomas disponibles
Removing and Filling the Milk Tank
1. Pull the lower part of the milk tank slightly upwards and
forwards.
2. Remove the cover from the milk tank.
3. Fill the milk tank with barista milk, barista milk alternative
or 3 % whole milk. The fill level must be between MIN
and MAX. The optimum milk temperature is 8 °C.
4. Place the cover back on the milk tank. Ensure that the
milk pipe is installed. Refit the milk tank to the appliance.
It must audibly click into place.
- If the milk tank was removed when the appliance was
switched on, a beep will sound when the milk tank is
removed or inserted.
- If the milk tank is not inserted correctly, a safety switch
prevents steam from escaping.
Initial Start-up
CAUTION:
The appliance must be cleaned with the cleaning func-
tion, especially before putting it into operation for the first
time or if it has not been used for a long time. Do not use
coffee powder during this procedure!
1. Fill the water tank and the milk tank with clean, fresh
water up to the MAX mark. Close the lid of the water tank
and reinsert the milk tank with the cover.
2. Insert the filter holder.
3. Set the control on the top of the milk tank to position .
4. Swivel the milk nozzle outwards with the adjustment
lever on the milk tank.
5. Place a suitable container (heat-resistant / approx.
500 ml) under the brewing head. If necessary, change
the length of the milk nozzle as previously described.
6. Switch on the appliance. The appliance starts with the
heating process. The heating plate becomes hot. Wait
until all control lamps light up.
7. Press the button (5) for a large cup of latte. Water starts
to flow through. Allow 2 – 3 cups to run through. It is best
to empty the container after each cycle.
WARNING: Risk of Burns!
The water in the container and the milk nozzle are hot!
8. Empty the container and place it back under the milk
nozzle.
9. To carry out the cleaning function, press and hold the
CLEAN / CAPPUCCINO button for 3 seconds. A beep
PC-ES-KA1266_IM_01.2024
sounds and the four control lamps on the left flash alter-
nately in a circle.
WARNING: Risk of Burns!
• During this process, a lot of hot steam is generated
and the milk pipe is rinsed with hot water.
• The water in the container and the milk nozzle are
hot!
When the process is complete, all control lamps pulsate.
The appliance is ready for operation when all control
lamps light up.
Programming the Espresso Coffee Quantity
You have the option of changing the factory-set coffee
quantity. Standard quantities for a small and a large cup of
espresso are set at the factory. To change these according
to your wishes, proceed as follows:
1. Fill the water tank with sufficient water and reinsert it.
2. Fit the filter holder without the coffee grounds.
3. Place a cup under the brew head.
4. Insert the mains plug into a socket and switch on the
appliance.
5. Wait until all control lamps light up. Then press and hold
button (3) or button (6) for at least 3 seconds.
6. As soon as the desired amount is reached, press the
button again.
- A beep sounds and all control lamps light up. The
appliance is now ready for use again.
Delete Programmed Coffee Quantity
Proceed as follows to delete the individually programmed
coffee quantity and restore the standard quantity:
1. Fill the water tank with sufficient water and reinsert it.
2. Wait until all control lamps light up.
3. Then press and hold the button (4) for a large cup of
cappuccino for approx. 3 seconds.
- To indicate that the programming has been cancelled,
a beep sounds and all control lamps flash 5 times.
The appliance is now ready for use again.
Insert and Remove Filter Inserts
• There are guide lugs on the filter inserts. These must be
inserted into the notch of the filter holder. Then turn the
filter insert by 90 degrees so that it does not fall out when
emptying later.
• To be able to remove the filter insert, it must be turned in
such a way that the guide nose is again in the notch of
the filter holder. Now the filter insert can be removed.
Pull-out Base for Smaller Cups
For small cups, pull the additional stand out of the appliance
until you hear it click into place. The base can also be
removed from the appliance for easy cleaning.
17
03.01.24
