Idiomas disponibles
Idiomas disponibles
Remote Control Searchlight Model 60080-Series
FEATURES
• High Output Halogen Sealed Beam Lamp
• Sleek Design
• Rugged Construction
• Full 360° Rotation
• Weather Resistant Remote Control
• Corrosion Resistant Lexan® Housing
• Supplied with 15 ft. (4.5m) Cable with Easy Plug-in Connec-
tions
APPLICATION
Ideal for mid-size boats to locate buoys, moorings, channel
markers, etc. Ideal for larger motorhomes and bus conversions
to pinpoint road signs, campsites, or use as a backup light.
Model Number
60080-0012
60080-0024
INSTALLATION INSTRUCTIONS
LIGHT MOUNTING
Select a location for the light which will allow a clear beam
projection forward and as far aft as possible. Searchlight base
should be mounted on a level, flat surface. A mounting block
between the searchlight base and mounting surface can be
used. The block should be contoured to fit the deck so the
searchlight base is level.
See mounting template attached for plug and cable required
clearance.
1. Mount light with foot of base towards the direction of most
intended use (front of circular base is marked "front") with
gasket under light base.
2. Feed wire through hole and secure light in place.
NOTE: Cable connectors are provided for easy wiring
connections.
Mounting hardware is provided;
4 – 1/4-20 x 2" (6.5 mm x 51 mm) bolts
4 – lockwashers
4 – flatwashers
CONTROL MOUNTING
Choose a location for the main control near the helm which will
allow convenient operation. Control may be mounted on verti-
cal, horizontal, or inclined panel.
1. Route power leads (supplied by customer) from the volt-
age source to control.
NOTE: Wiring must be 16 gauge with a maximum run of
15 ft. (4.5m)
2. Crimp terminals (supplied) onto the power leads,
Voltage
Amps
12 Vdc
4
24 Vdc
2
SPECIFICATIONS
Voltage:
Amp Draw:
Elevation Angle (degrees):
Housing Material:
Candle Power:
Lux Valve:
W A R N I N G
Burn Hazard. Do not touch lense when light is on.
Do not operate with storage cover over light.
Watts
50
50
NOTE: Larger terminal is crimped to positive lead, smaller
terminal is crimped to negative lead.
3. Insert wiring cable through back of hole and plug into control.
4. Use bedding compound or sealant to water-proof control.
5. Secure control with self-tapping screws provided.
OPTIONAL
SECONDARY CONTROL MOUNTING
If an additional control station is desired, use control kit 43670-
0004. Mount secondary control in same manner as main con-
trol. Mount station selector panel near the main control (fly-
bridge or lower).
1. Cut a 2" x 1-3/8" (51 mm x 35 mm) opening for station
selector panel within a 1 foot radius of the control.
2. Route secondary control cable from station selector panel
to secondary control location (cable acquired separately—
see cable listing).
3. Insert station selector panel thru mounting hole and attach
connectors to mating connectors from control and search-
light. The connector marked "flybridge" to go to flybridge
control and the connector marked "lower" to lower control.
The connector to the nearest control can be plugged directly
into the control. See diagram.
4. Use bedding compound or sealant to waterproof station
selector panel mounting.
5. Secure panel with self-tapping screws provided.
2
12 Vdc, 24 Vdc
4 (12V), 2 (24V)
Up 30°, Down: 30°
Lexan
175,000
15@ 382ft. (100m)
® LEXAN is a registered trademark of General Electric Company.
Bulb Type
Weights lb (kg)
SPOT
9 (4.1)
SPOT
9 (4.1)
