Idiomas disponibles
Idiomas disponibles
EXTENSION C ORDLENGTH
WireSize
A.W.G.
Upto 50ft..................................
16
50-100 ft...................................
14
NOTE: U singextension c ordsover100ft.longis not
recommended.
MOTOR
The 120 Volt AC universal motor has the following
specifications:
Voltage ...................................
120
Amps .....................................
12
Hertz .....................................
60
Phase ..................................
Single
Cutterhead RPM .........................
10,000
ELECTRICAL
CONNECTIONS
WARNING:
Make sure unit is turned off and discon-
nected from power source before inspecting any wiring.
The motor is assembled with an approved three con-
ductor cord to be used on 120 volts as indicated. The
power supply to the motor is controlled by a double
pole locking rocker switch.
•
Remove the key to prevent unauthorized use.
The power lines are inserted directly onto the switch.
The green ground line must remain securely fastened
to the frame to properly protect against electrical shock.
Refer to Figures 10-20, pages 7-9.
DESCRIPTION
Craftsman 61/8 ' ' jointer/planer
is used to surface the
faces and edges of boards, produce a flat surface on
warped boards and shape bevels, chamfers and tapers.
The jointer/planer
features cast iron infeed and outfeed
tables, cast iron body with smooth work surfaces and
lead screws for precise table height adjustment.
Balanced guide fence tilts 45 ° (inward) and 45 ° (out-
ward). Built-in blower for chip removal. Tool comes with
locking rocker switch with removable key and push
blocks. Jointer/planer
easily handles rough-cut lumber,
planes hard and soft woods up to 61/8 ' ' wide using a two
blade cutterhead, and takes cuts up to 1/8".
SPECIFICATIONS
Table size ............................
285/8x 61/4"
Fence size ...........................
22%x 33/4"
Blade width ...............................
61/J '
Maximum cut ...........................
1/8" D eep
Cuts Per Minute .........................
20,000
Overall Size .......................
285/8x 18 x 12"
Dust collection port ..................
2V2" Diameter
Weight ..................................
70 Ibs
Motor ...............................
12A, 120V
OPERATION
SAFETY
RULES
Jointing
is a surfacing operation in which a small
amount of wood is removed from the edges and faces
of boards to get smooth, straight and even surfaces
such that the two edges that run across the planing
blocks would fit together perfectly, forming a seamless
joint.
Planing refers to the sizing of lumber to a desired thick-
ness while creating a level surface parallel to the oppo-
site size of the board. Depth of cut is the term used to
indicate how deep the blades will cut into the workpiece.
WARNING:
Operation of any power tool can result in
foreign objects being thrown into eyes which can result
in severe eye damage. Always wear safety goggles
complying with United States ANSI Z87.1 (shown on
package) before commencing power tool operation.
WARNING:
For your own safety, read all of the
instructions and safety precautions before operating
tool.
•
Know general power tool safety. Make sure all pre-
cautions are understood (see pages 2, 3 and 6).
•
Whenever adjusting or replacing any parts on
jointer/planer,
turn switch off and remove plug from
power source.
•
Make sure all guards are properly attached and
securely fastened.
•
Make sure all moving parts are free from interference.
•
Always wear eye protection or face shield.
•
Make sure blades are aligned and properly attached
to cutterhead.
•
Do not plug in jointer/planer unless switch is in OFF
position. After turning switch on, allow jointer/planer
to come to full speed before operating.
•
Keep hands clear of all moving parts.
•
Do not force cut. Slowing or stalling will overheat
motor.
•
Use quality lumber. Blades last longer and cuts are
smoother with good quality wood.
•
Do not perform jointing/planing
operations on materi-
al shorter than 8W', narrower than 3/4",or less than
1/4"thick
•
Never make jointing cut deeper than 1/8".
•
Always keep cutterhead and blade guards in proper
working condition.
•
Maintain the proper relationships of infeed and out-
feed table surfaces and cutterhead blade path.
•
Do not back the work toward the infeed table.
•
Support the workpiece adequately at all times during
operation; maintain control of the workpiece.
•
Use hold-down/push
blocks for jointing material nar-
rower than 3" or planing material thinner than 3".
•
Take precautions against kickback. Do not permit any-
one to stand or cross in line of cutterhead's rotation.
Kickback or thrown debris will travel in this direction.
6
