Idiomas disponibles
Idiomas disponibles
A
A
A
WARNING:
Do not allow familiarity with products to
make you careless. Remember that a careless frac-
tion of a second is sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side
shields marked to comply with ANSI Z87.1. Failure
to do so could result in objects being thrown into
your eyes resulting in possible serious injury.
WARNING:
Do not use any attachments
or
accessories not recommended
by the manufac-
turer of this product. The use of attachments or
accessories not recommended
can result in serious
personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
[] Driving screws with screwdriver bits
[] Light-duty drilling
_
WARNING:
Battery products are always in operat-
ing condition. Therefore, the switch should always
be locked when not in use or carrying at your side.
[] Do not attempt to use this product if the battery cap is
not securely closed.
DIRECTION
OF ROTATION
SELECTOR
(FORWARD/REVERSE/CENTER
LOCK}
See Figure 3, page i.
The direction of bit rotation is reversible and is controlled
by a selector located above the switch trigger. With the
screwdriver held in normal operating position, the direc-
tion of rotation selector should be positioned to the left
of the switch trigger for forward motion. The direction is
reversed when the selector is to the right of the switch
trigger.
Setting the direction of rotation selector in the OFF (center
lock) position helps reduce the possibility of accidental
starting when not in use.
CAUTION:
To prevent gear damage, always al-
low the collet to come to a complete stop before
changing the direction of rotation.
To stop the screwdriver, release the switch trigger and al-
low the collet to come to a complete stop.
NOTE: The screwdriver will not run unless the direction of
rotation selector is pushed fully to the left or right.
BATTERY
PROTECTION
FEATURES
Craftsman _ 4 V lithium-ion batteries are designed with
features that protect the lithium-ion cells and maximize
battery life.
If the tool stops during use, release the trigger to reset
and resume operation. If the tool still does not work, the
battery needs to be recharged.
TO INSTALL
/ REMOVE
BATTERY
PACK
See Figure 2, page i.
_IIL WARNING:
Always remove battery pack from the
product when you are assembling parts, making
adjustments, cleaning, or when not in use. Remov-
ing battery pack will prevent accidental starting that
could cause serious personal injury.
To install the battery
pack:
[] Unscrew the battery cap.
[] Insert the battery pack in the direction shown. Make
sure the raised rib on the battery pack aligns with the
groove in the compartment.
[] Place the cap over the battery pack and push down
until the cap meets the threads at the end of the
battery compartment.
[] Screw the cap on securely.
To remove the battery
pack:
[] Unscrew the cap. The battery pack will disconnect and
be easy to remove.
TWO=SPEED
GEAR TRAIN
See Figure 4, page i.
The screwdriver has a two-speed
gear train designed
for low (Position
1) or high (Position 2) speeds. A slide
switch is located on top of the screwdriver to select the
speed setting. When using screwdriver in the low speed
range (Position
1}, speed will decrease and unit will have
more power and torque. When using screwdriver in the
high speed range (Position 2), speed will increase and
unit will have less power and torque.
Use the high speed setting to drill holes, and use the low
speed setting for driving screws.
TO LOAD/RELEASE
BITS
See Figure 5, page L
The quick-release collet on the screwdriver is a quick
change chuck designed to accept any 1/4 in. hex bits,
including 1 in. and 2 in. driver bits. Insert the bit into the
chuck and push as far as possible until the chuck locks
onto the bit. To remove a bit, push rubber collar forward,
and then pull the bit straight out of the chuck.
ADJUSTABLE
TORQUE
CLUTCH
This screwdriver is equipped with an adjustable torque
clutch for driving different types of screws into differ-
ent materials. The proper setting depends on the type of
material and the size of screw you are using.
8 - English
