Idiomas disponibles
Idiomas disponibles
Replacing the light bulb
WARNING: PLEASE ENSURE THAT YOUR APPLIANCE IS DISCONNECTED
FROM YOUR MAINS SUPPLY BEFORE ATTEMPTING TO REPLACE THE
LIGHT BULB.
o Press the rear end of the bulb cover until the sides release and then lift
the bulb cover clear of the bulb.
o Change the present light bulb with a new one. The replacement bulb
should not have a greater rating than 15 W; (an E14 15 W bulb should be
used).
o Replace the light cover and after waiting five minutes, reconnect your
plug to your mains supply.
INSTALLATION
IMPORTANT: Before installation and usage read all the instructions
and make sure that the voltage (V) and the frequency (Hz)
indicated on the rating plate are exactly the same as the voltage
and frequency in your home. The rating plate can be found on the
front left edge of the
inside of the refrigerator.
The manufacturer declines all responsibility in the event of the installer
failing to observe all the accident prevention regulations in force, which
are necessary for normal use and the regular operation of the electric
system.
Electrical connection
YOUR REFRIGERATOR IS INTENDED FOR FITTED AND
PERMANENT INSTALLATION.
We recommend that the appliance is connected by a qualified
electrician, who is a member of the N.I.C.E.I.C. and who will comply
with the I.E.E. and local regulations.
o
Your refrigerator comes supplied with a 13 amp plug fitted. If in
future you need to change the fuse in this plug, then a 13 amp ASTA
approved (BS 1362) fuse must be used.
o The wiring in the mains lead is coloured as follows:
Brown Live
Blue Neutral
Green and yellow Earth
o
As the colours of the wires in the appliance's mains lead may not
correspond with the coloured markings identifying the terminals in your
spur box, please proceed as follows:
The brown wire must be connected to the terminal marked "L" (live), or
coloured red.
The blue wire must be connected to the terminal marked "N" (neutral), o
coloured black.
The green and yellow wire must be connected to the terminal marked "E"
(earth), or by the earth symbol, or coloured green and yellow.
o
When the connection is completed, no stray strands or cut wire
should be present. The cord clamp must be secured over the outer
sheath.
Positioning
o
It is advisable that your appliance is only installed in a location
where the ambient temperature of the room, corresponds with the
climate classification that is stated on the rating plate of your appliance.
Your appliance may not function correctly if the ambient temperature
falls outside of the following ranges.
o extended temperate (SN): 'this refrigerating appliance is intended to be
used at ambient temperatures ranging from 10 °C to 32 °C';
o temperate (N): 'this refrigerating appliance is intended to be used at
ambient temperatures ranging from 16 °C to 32 °C';
o subtropical (ST): 'this refrigerating appliance is intended to be used at
ambient temperatures ranging from 16 °C to 38 °C'
o tropical (T): 'this refrigerating appliance is intended to be used at ambient
temperatures ranging from 16 °C to 43 °C';
o
o
Your appliance should not be located in direct sunlight or exposed to
continuous heat or extremes of temperature (e.g. next to a radiator or
boiler).
o The door should be able to open completely and freely.
o
The appliance should be situated so you can easily access the
food that is stored in it.
o
You should check whether there is an electrical socket available,
which will be accessible after your appliance is installed.
Reversing the door of your appliance
This procedure MUST be completed before the furniture door is attached.
Any parts that you remove from the appliance whilst reversing the door,
should be retained for later use.
WARNING - Take care when opening the hinges, they are sprung loaded
and there is the risk of injury if they close on your hand.
Tools required:
o Phillips screwdriver
o Flat bladed screwdriver
o
Slacken the retaining screws (1) on the appliance and then
carefully remove the appliance door.
o
Place the appliance door on a cushioned surface, so that it
does not get damaged.
o Lever off the cover caps (3).
o
Insert the retaining screws (1) into the opposite side of the
appliance from their original position. These screws should be partially
tightened but not fully tightened.
o
Remove the door retaining screws (2) and then reverse the
position of the top and bottom hinge (as shown in the above diagram).
o Reattach the appliance door and then fully re-tighten the retaining screws
(1) and the door retaining screws (2).
o
Insert the cover caps (3) into the holes that are now exposed on
the right hand side of the cabinet.
IMPORTANT: Check that the door opens and shuts correctly,
without fouling, after you have completed the door reversal
process.
After the door has been reversed, you should check the door seal of
the appliance. The seal should not be creased or crushed; otherwise
there will be a gap between it and the inside of the door.
18
