Idiomas disponibles
Idiomas disponibles
ASSEMBLY INSTRUCTIONS
1. Fasten the two larger rear caster wheels (No.1) on the Base structure with Bolts, washers, spring
washers and nuts (Face bolts up when installing.)
2. Fasten the smaller two caster wheels (No.3) on the Base structure with Bolts (No.4), spring washers
(No.5). (Face bolts up when installing.)
3. Fasten the remaining larger two caster wheels (No.1) on the front legs (No.2) with bolts, washers,
spring washers and nuts.
4. Slide the legs (No.2) into front of the base (No.6).
5. Fasten the guide plates (No.12), to the base frame (No.6) and front legs (No.2) with bolts (No.11),
washers (No.13) and nuts (No.14). Lift one side of the base to align the hole on the frame to the hole
on each front leg (No.2), then insert the Ring Pins (No.10) into the hole and insert the Cotter-pin
(No.9) into the hole of the Ring Pins.
6. Use Bolts (No.4) and Spring washers (No.5) to fasten the Handle (No.27) to the Post (No.21).
7. Use two Bolts (No.19), washers (No.8) and Nuts (No.7) to connect the bottom of the Post (No.21) to
the Base Frame (No.6).
8. Use two Bolts (No.15), Washers (No.17) and Nuts (No.18) to connect the lower ends of the Supports
(No.16) to the inside of the base (No.6). Then use Bolt (No.26), Washer (No.22) and Nut (No.18) to
connect the top ends of the Support to the post (No.21), check to make sure the nuts were tightened,
and tighten the nuts in step 6.
9. Use Bolt (No.28), Washer (No.29) and Nut (No.14) to attach the Boom (No.31) to the top of the Post
(No.21), tighten Nut (No.14) so that the boom (No.31) can rotate freely, do not over tightened boom
needs to be able to rotate freely.
10. Use Bolt (No.20), Washer (No.22) and Nut (No.18) to fasten the lower end of the Long Ram (No.25) to
the Post (No.21). Then use Bolt (No.30), Washer (No.22) and Nut (No.18) to fasten the top of the
Long Ram to the Boom (No.31).
11. Slide the Boom Extension (No.33) into the Boom (No.31) and use Bolt (No.32), Washer (No.22) and
Nut (No.18) to secure at the desired load rating. Use Bolt (No.34), Washer (No.8) and Nut (No.7) to
attach the Hook and Chain (No.35) to the end of the Boom Extension. (The boom has four different
load ratings; select desired rating before use.)
INSPECTION
• Inspect the equipment carefully before each use. Ensure the equipment is not damaged,
excessively worn, or missing parts.
• Do not use the equipment unless it is properly lubricated.
• Using equipment that is not in good clean working condition or properly lubricated may cause
serious injury.
• Inspect the work area before each use. Make sure it is free and clear of any potential hazards.
• To maintain the equipment and user safety, the responsibility of the owner is to read and follow
these instructions.
• Inspect the equipment for proper operation and function.
• Make certain all equipment operators are properly trained; understand how to safely and correctly
operate the unit.
• Allow unit operation only with all parts in place and operating properly.
• Use only genuine replacement parts.
• Service and maintain the unit only with authorized or approved replacement parts; negligence will
make the equipment unsafe for use and void the warranty.
• Carefully inspect the unit on a regular basis and perform all maintenance as required.
• Store these instructions in the handle of your equipment.
• Keep all decals on the unit clean and visible.
• You should inspect the product for damage, wear, broken or missing parts (e.g.: pins) and that all
components function before each use. Follow lubrication and storage instructions for optimum
product performance.
BGS technic KG
Bandwirkerstr. 3
D-42929 Wermelskirchen
Tel.: 02196 720480
Fax.: 02196 7204820
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
