Idiomas disponibles
Idiomas disponibles
Graphics areincluded l ater i nthissection.
Remove
and Replace Handles
1. Using a %2" Allen wrench, loosen the two set screws located
on the side of each handle. See Graphics 1 and 2.
2. Pull the handle straight out from the door. Make sure you
3.
keep the screws for reattaching
the handles,
3. To replace the handles, reverse the directions.
4.
Remove
Doors and Hinges
Electrical Shock Hazard
Disconnect power before removing
doors.
Failure to do so can result in death or electrical shock.
IMPORTANT:
•
Remove food and any adjustable door or utility bins from
doors,
•
All graphics referenced in the following instructions
are
included later in this section after "Final Steps."
TOOLS NEEDED: %6", %", 1/4"hex-head socket wrench,
#2 Phillips screwdriver, and a flat-blade screwdriver.
1. Unplug refrigerator or disconnect power.
2. Keep the refrigerator doors closed until you are ready to lift
them free from the cabinet.
NOTE: Provide additional support for the refrigerator door
while the hinges are being removed. Do not depend on the
door gasket magnets to hold the door in place while you are
working.
3=
Starting with the right-hand side door, remove the parts for
the top hinge as shown in Top Hinge graphic. Lift the
refrigerator door from the bottom hinge pin,
NOTE: On some models, remove the shim from the bottom
hinge pin and keep it for later use. See Bottom Hinge graphic,
4=
Before removing the left-hand side door, disconnect
the
wiring plug located on top of the top hinge by wedging a flat-
blade screwdriver or your fingernail between the two
sections. See Wiring Plug graphic.
NOTE: The green, ground wire remains attached to the hinge,
5=
Remove the parts for the top hinge as shown in Top Hinge
graphic. Lift the left-hand side door from the bottom hinge
pin.
NOTE: On some models, remove the shim from the bottom
hinge pin and keep it for later use. See Bottom Hinge graphic.
Replace Doors and Hinges
1. Assemble the parts for the top hinge as shown in Top Hinge
graphic. Do not tighten the screws completely.
2. Replace the parts forthe bottom hingeas shown inBottom
Hinge graphic. Tightenscrews.Replace therefrigerator
door.
NOTE: Provideadditional supportforthe refrigerator
door
while the hingesarebeingmoved. Do notdepend on thedoor
gasketmagnets to holdthedoor inplacewhileyou are
working.
Align the door so that the bottom of the refrigerator door
aligns evenly with the top of the freezer drawer. Tighten all
screws,
Reconnect the wiring plug on top of the left-hand side
refrigerator door.
5. Replace the top hinge covers.
Remove
and Replace Freezer
Drawer Front
IMPORTANT: Two people may be required to remove and replace
the freezer drawer front. Graphics are included later in this
section.
Remove
Drawer
Front
1. Open the freezer drawer to full extension.
2. Loosen the four screws attaching the drawer glides to the
drawer front. See Drawer Front Removal graphic.
NOTE: Loosen screws three to four turns. Keep the screws in
the drawer front.
3. Lift drawer front upward and off the screws. See Drawer Front
Removal graphic.
Replace Drawer
Front
1. Slide the drawer glides out of the freezer compartment.
Insert
the screws in the top of the drawer front into the slots in the
drawer brackets. See Drawer Front Replacement graphic.
2. Pull the drawer brackets toward you to position the two
screws in the bottom of the drawer front into the brackets.
See Drawer Front Replacement graphic.
3. Completely tighten the four screws.
Final Steps
Electrical
Shock Hazard
Plug into a grounded
3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug in refrigerator to a grounded 3 prong outlet.
2. Return all removable door parts to doors and food to
refrigerator.
