Idiomas disponibles
Idiomas disponibles
ILM Tag
Technical Data
Specifications
Specification
Frequency range, UWB
Transmitting power, UWB
Maximum Radio Output Power
Frequency Range
Radio Technology
(MHz)
UWB
5500-7500
Declarations
EU DECLARATION OF CONFORMITY
We, Atlas Copco Industrial Technique AB, SE-105 23
STOCKHOLM SWEDEN, declare under our sole responsi-
bility that the product (with name, type and serial number, see
front page) is in conformity with the following Directive(s):
2011/65/EU (RoHS),2015/863/EU (RoHS amendment),
2014/53/EU (RED)
Harmonized standards applied:
EN 301 489-33 V2.2.0, EN 301489-1 V2.2.0, EN 302 065-2
V2.1.1, EN 62368-1:2014
Authorities can request relevant technical information from:
Aleksandra Duric, Product Compliance Manager, Atlas
Copco Industrial Technique AB, SE-105 23 Stockholm Swe-
den
Stockholm, 2 May 2022
Carl von Schantz, Managing Director
Signature of issuer
WEEE
Information concerning Waste of Electrical and Electronic
Equipment (WEEE):
This product and its information, meets the requirements of
the WEEE directive/regulations (2012/19/EU), and must be
handled in compliance with the directive/regulations.
The product is marked with the following symbol:
5500 MHz - 7500 MHz
-10.21 dBm
Maximum Trans-
mit Power EIRP
(dBm)
-10.21
© Atlas Copco Industrial Technique AB - 9846 0022 00
Products marked with a crossed-out wheeled bin symbol and
a single black bar underneath, contain parts that must be han-
dled in compliance with the WEEE directive/regulations. The
entire product, or the WEEE parts, can be sent to your "Cus-
tomer Center" for handling.
RF Exposure Statement
This portable transmitter has been tested and found to comply
with FCC General Population RF Radiation Exposure limits
set forth for an uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines. The antenna used
for this device must not be co-located or operating in conjunc-
tion with any other antenna or transmitter.
FCC and ISED Compliance Statement
This device complies with part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
FCC Responsible party:
Name: Tim Copacia
Position: Product Manager
Address: 3301 Cross Creek Parkway
MI 483 26 Auburn Hills
United States
Mobile: +1 5862020902
Email: [email protected]
The device is only in compliance if no changes or modifica-
tions are made to the device. The antenna is fixed to the de-
vice and no change in antenna or fixation of the antenna is ac-
ceptable and such modification is considered to violate the
Compliance Statement.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pur-
suant to part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the in-
structions, may cause harmful interference to radio com-
munications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV tech-
nician for help.
ISED Compliance Statement:
Safety Information
3
