Idiomas disponibles
Idiomas disponibles
INTRODUCTION
This device is a generator inverter current (DC) suitable to
the MMA welding. Thanks to the inverter technology which
allows achieving high performances while keeping small
size and weight, the welder is portable and easy to
handle. The device is suitable for welding with coated
electrodes rutile and can be connected to power
generators with power equal to or higher than that
reported in Table 2. It is equipped with "HOT START",
"ARC FORCE" and "ANTI STICK" functions (for more
details please refer to the GENERAL PART manual
included in the package).
DESCRIPTION OF THE MACHINE
Fig 1
A Welding current Knob.
B Thermal protection LED indicator.
C Negative pole (-).
D Positive pole (+).
E ON-OFF switch.
F Power Cord.
INSTALLATION
The installation must be made by trained personnel in
compliance to the standard IEC 60974-9 and the current
and local legislation. To lift the machine it must be used
the handle positioned on top of the product with the
machine in OFF position. The input voltage must match
the voltage indicated on the technical plate located on the
product.
Use the machine on electric system having supply
features and power protection (fuse and / or differential
switch) that are compatible with the current required for its
use. For more details see the information on the plate
placed on the machine.
HOW USE IT
Warning: Use all precautions required in the safety
general manual before operating the welder, reading
carefully the risks linked to the welding process.
ELECTRODE WELDING (MMA)
•
Connect the plugs of the earth clamp and the
electrode holder to the connectors of the machine (Fig 1,
C and D) rotating the attack in order to ensure a good grip.
Choose the polarity Fig.2 (1. forward or 2. reverse)
depending on the coating of the electrodes (for more
information see the information on the electrodes
packaging).
•
Connect the earth clamp to the work piece to be
ANOMALIES
The device is not delivering current
and the yellow indicator LED of
thermal protection lights up.
The device is on but it is not
delivering current.
Your unit does not weld correctly.
Instable arc
The electrode melts
ENGLISH
welded trying to establish a good point of contact between
the metal and the clamp, as close as possible to the area
to be welded, insert the electrode into the electrode
holder.
•
welding machine by pressing the switch (Fig 1, E) to the ON
position. For welding machines without a plug (115/230V
models), connect a normalised plug (2P + T) - having sufficient
capacity- to the power cable and prepare a mains outlet fitted
with fuses or an automatic circuit-breaker; the special earth
terminal should be connected to the earth conductor (yellow-
green) of the power supply line.
•
of the type of electrode selected (Tab. 1).
•
protections for the security.
•
and release the electrode from the electrode holder
TIG WELDING (only for the TIG type) Fig.3
1.
torch to the poles of the device; choose the polarity (forward or
reverse) in relation to the type of material to be welded
2.
3.
4.
5.
6.
valve
7.
the welder
8.
between the two phases
Stopped the welding, turn off the machine
THERMAL PROTECTION
If the machine is used for hard work cycle, the thermal
protection device will protect the machine from over
heating. The yellow LED ON indicates that the thermal
protection is on. It is possible to start welding again once
the LED is off.
MAINTENANCE
The all maintenance services must be done from qualified
personnel in compliance to the norm (IEC 60974-4).
TROUBLESHOOTING
CAUSES
The welder thermal
protection has turned on.
The cable of the earth
clamp or electrode holder
is not connected to the
welder.
Polarity error
TIG
-)Default coming from the
tungsten electrode
-)Too important gas flow
rate
Polarity error
4
Insert the plug into the power outlet and turn on the
Select the welding current (FIG 1, A) as a function
Start the welding operation using all the necessary
When welding is completed, turn off the machine
Connect the connectors of the earth clamp and of the
Connect the earth clamp to the work piece
Connect the torch gas tube to the gas cylinder
Select the TIG mode
Select the welding current
Select the gas flow of the gas cylinder and open the torch
Connect the power cord to the power supply and turn on
Use the torch to weld as in the following without a puse
Touch the piece with the electrode
Lift the electrode from the piece
about 2-5 mm
Wait for the end of the cooling
time, around 2 minutes. The
indicator led turns off.
Turn off the machine and check the
connections.
. Check the polarity advised on the
electrodes packaging.
-) Use a tungsten electrode with the
adequate size
-) Reduce gas flow rate
Check that the earth clamp is really
connected to +
REMEDIES
