TFA 30.3034 Instrucciones De Uso página 8

TFA_No_30.3034.10_Anl_02_23
Wireless thermometer
5.2. Transmitter (Fig. 2)
D1: Wall mount hole
D3: Support for table standing
6. Getting started
6.1 Insert batteries
• Open the battery compartment of the base station and the transmitter
(screwed) and place both instruments on a desk with a distance of
approximately 1.5 meter. Check that no other electronic devices are close.
• Insert the batteries 2 x 1,5 V AAA into the battery compartment of the
transmitter and immediately afterwards 2 x 1,5 V AA in the base station,
observing the correct polarity.
• A brief beep tone will sound and all LCD segments will light up for a short
moment.
6.2 Reception of outdoor temperature
• The base station automatically starts scanning the 433 MHz signal to reg-
ister the thermo sensor unit after batteries are inserted.
minutes on the LCD of the base station.
• Note: DO NOT PRESS ANY KEY during the learning period. If the outdoor
temperature is not displayed or if any key is pressed before the outdoor
temperature signal is received and when changing batteries you will need
to follow the battery installation procedure again. Please wait 10 sec-
onds before inserting the batteries again.
• You can also start the outdoor transmitter search manually later on (for
example when the outdoor transmitter is lost or the batteries are
changed).
• Press the RESET/CH/+ button for 3 seconds. "---" and
6.3 Manual setting
• Press the SET/MIN/MAX button for 3 seconds.
• The "24Hr" indicator is flashing. Press the RESET/CH/+ button to choose
12 HR or 24 HR system.
• Confirm with the SET/MIN/MAX button.
• The minute digit is flashing. Press the RESET/CH/+ button to adjust mi-
nutes. Confirm with the SET/MIN/MAX button. Set hours in the same way.
14
26.02.2023 16:33 Uhr Seite 8
D2: Battery compartment
D4: Support for wall mounting
appears for 3
are displayed.
Wireless thermometer
• Press the SET/MIN/MAX button again and with the RESET/CH/+ button
you can change between °C or °F as temperature unit.
• Confirm with the SET/MIN/MAX button.
• The device will automatically quit the setting mode if no button is pressed
for 30 seconds.
• Press and hold the RESET/CH/+ button in the setting mode and you will
enter fast mode.
6.4 Alarm setting
• Press the SET/MIN/MAX button in normal mode.
• 12:00 (default) is displayed or the last adjusted alarm time.
• Press and hold the SET/MIN/MAX button for three seconds.
• The minute digit is flashing. Press the RESET/CH/+ button to adjust min-
utes.
• Press the SET/MIN/MAX button again and you can adjust the hours with
the RESET/CH/+ button.
• Holding the RESET/CH/+ button, you will enter fast mode.
• Confirm with the SET/MIN/MAX button and the display shows the current
adjusted alarm time.
• Press the RESET/CH/+ button and the alarm function is activated.
• The alarm symbol appears on the display.
• Press any button to stop the alarm.
7. Maximum/Minimum function
• Press the SET/MIN/MAX button in normal mode.
• The last adjusted alarm time appears on the display.
• Press the SET/MIN/MAX button again to show the minimum ("MIN") val-
ues of indoor and outdoor temperature. Press the SET/MIN/MAX button
again to show maximum ("MAX") values.
• Press and hold the RESET/CH/+ button for 2 seconds while the maximum
or minimum values are displayed to clear the recorded maximum read-
ings.
8. Additional transmitters
• If you like to connect additional remote sensors (max. 3), repeat the
installation procedure for all extra sensors. The wireless thermometer
will number the sensors in the order of set-up automatically.
15