Idiomas disponibles
Idiomas disponibles
GB
MT
•
Advance the workpiece with both hands, making sure that
you use a push stick (18) as a pushing aid in the vicinity of
the saw blade.
•
Always push the workpiece through to the end of the riving knife.
Caution! In the case of short workpieces, the
push stick should be used from the beginning of
the cutting process.
Cutting very narrow Workpieces
30
(Fig.
)
For longitudinal cuts of very narrow workpieces with a width of
30 mm and less, a push block must be used without fail.
•
The parallel stop should be adjusted to the cutting width of
the workpiece.
•
Press the workpiece with the push block against the stop rail
and push the workpiece with the push stick (18) through to
the end of the riving knife.
- The scope of delivery does not include a push block. You
can purchase a push block from specialist shops.
- Replace any worn push blocks in good time.
Performing Bevel Cuts
31
(Fig.
)
All bevel cuts are made using the parallel stop (16).
-
Adjust the saw blade (4) to the desired angle.
-
Adjust the parallel stop (16) according to the workpiece
width and height.
-
Perform the cut according to the workpiece width
Performing Transverse Cuts
25
32
(Fig.
+
)
-
Push the transverse stop (36) into one of the two grooves (33)
of the saw table. Adjust to the desired angle. The left groove
(33) is to be used if the saw blade (4) also has to be posi-
tioned at an oblique angle.
This will prevent your hand and the transverse stop from com-
ing into contact with the saw blade guard.
Press the workpiece fi rmly against the stop rail (35) on the
-
cross stop (36).
-
Switch on the saw.
-
Push the transverse stop (36) and workpiece in the direction
of the saw blade in order to perform the cut.
-
Caution: Always hold the guided workpiece fi rmly and never
the free workpiece which is cut off.
-
Always push the transverse stop (36) so far forwards until the
workpiece is completely cut through.
-
Switch the saw off again. Only remove sawing waste when
the saw blade has come to a standstill.
Cutting Chipboard
In order to prevent the cut edges chipping when the chipboard
is cut, the saw blade (4) should be adjusted so that it is not more
than 5 mm above the thickness of the workpiece.
Transport
33
34
(Fig.
+
)
1. Turn the power tool off before it is transported and disconnect
it from the power supply.
2. Pull off any suction hose, that may be connected, from the
suction adapter (17).
44
3. Insert the saw blade with the help of the crank handle (12).
By turning the saw blade (
downwards.
4. At least two people should carry the power tool. Do not hold
the power tool by the table width extensions. Please only use
the points as shown in Fig.
chine.
5. Protect the power tool against knocks, jolts and strong vibra-
tions, e.g. when it is transported in motor vehicles.
6. Secure the power tool against tilting and sliding.
7. Never use the protective devices for handling or transport.
Overload protection
35
(Fig.
)
If the motor is overloaded, it switches off automatically.
After cooling down, the motor can be switched on again.
-
Allow the motor to cool down
-
Press the overload protection switch (37).
-
Start the device as described under "Switching on and off".
Cleaning and Servicing
Remove the mains plug before carrying out any adjust-
ments, maintenance or repair work.
You should have any repair and maintenance work that is
not described in these instructions carried out by our Ser-
vice Centre. Only use original parts.
If replacement of the connecting cable becomes necessary, this
is to be carried out by the manufacturer or its agent in order to
avoid safety risks.
Perform the following cleaning and maintenance work regularly.
This guarantees reliable use for a long time.
Cleaning
The device must not be sprayed with water or
placed in water. Otherwise there is a risk of
electric shock.
•
Keep the safety devices, air vents and motor housing as free
of dust and dirt as possible. Wipe the device off with a clean
cloth or blow it out with compressed air at a low pressure.
•
We recommend that you clean the device immediately after
every use.
•
Clean the saw blades regularly.
•
Remove any dirt, such as resin, from the saw blades using
only solvents that do not impair the mechanical properties of
the saw blades.
•
Try to clean resinous surfaces with a damp, lukewarm cloth
that has been wrung out well. Make sure that no liquids can
get into the interior of the housing!
Alternatively, you can use a special cleaner (resin solvent) or
multispray. Please take notice of the safety information and
instructions provided by the manufacturer of the special clean-
er/multispray.
•
Do not use any detergents or solvents; these might attack the
plastic parts of the device.
•
Oil the moving parts once a month in order to extend the tool
life. Do not oil the motor.
– 4) anticlockwise, it moves
1
+
33
34
to transport the ma-
