Idiomas disponibles
Idiomas disponibles
1
Operating instructions for KoiFeeder Solar
Dear customer,
This operating manual contains important information on commissioning and use. Read the operating manual carefully before using the solar fish feeder. This applies particularly to the safety advice. Otherwise,
you may injure yourself or damage the solar feeder. Keep the operating manual for future use. If you pass the solar feeder on to a third party, be sure to hand over this operating manual as well. These operating
instructions can also be downloaded as a PDF file from our website www.outsideliving.com.
Safety instructions
This device may be used by children from the age of 8 upwards and also by people with physical,
sensory or mental disabilities or lacking suitable knowledge and experience, provided they are
supervised or have been instructed in the use of the device and understand the resulting hazards.
The solar feeder is intended for private use only and is not suitable for commercial applications.
Only use the solar feeder as described in this operating manual. Any other use is considered impro-
per and can lead to damage to property and/or personal injury. The solar feeder is not a toy. The
manufacturer or dealer accepts no liability for damage resulting from improper or incorrect use.
Make sure that the solar feeder is placed on a level and stable surface and cannot fall into the
water.
Check the solar feeder and scope of delivery
Risk of damage
If you open the packaging carelessly with a sharp knife or other pointed object, the solar feeder
or accessories may be damaged. Remove the solar feeder from the packaging. Check whether the
solar feeder or the accessories are damaged. If this is the case, contact the dealer immediately.
Assembly
After removing the solar feeder from the packaging, mount the feed chute (11) on the lower part of the housing (10) by inserting it into the guide. The feed chute (11) automatically locks into place at the end of the
guide.
Two different installation options are available for mounting on the pond:
1. Installation with ground anchors:
Insert the ground anchors (16) included in the scope of delivery into
the ground and connect them to the stands (15).
Connect the ground anchors (16) included in the delivery to the
stands (15) by inserting the ground anchors into the guide of the
stands. Then screw the ground anchors to the stands and press the
solar feeder into the ground along with the ground anchors.
Filling
Please consult a specialist aquarium retailer for information on the selection of suitable fish food. We recommend an appropriate fish food with a grain size of 3 – 10 mm for filling the solar feeder. To do so, open the
feed bucket cover (3) and fill the feed up to a maximum of just below the top edge of the feed bucket (5). To ensure that the feed is kept dry for a long time, we recommend that you place a desiccant in the desiccant
holder (4). Remove the desiccant holder (4), place a suitable desiccant inside and put the desiccant holder back into its device. The maximum size of the desiccant is: 75 x 75 x 15 mm.
Commissioning
K
Settings of the solar feeder
Basic settings: Switch on the solar feeder by setting the switch (14) to the „I" position and opening the cover of the control panel (13). If no buttons are pressed for 12 seconds, the input is terminated. Pressing the
selection key again takes you to the desired input.
Setting the time
Press the selection key (A) once and set the hours with the up (B) or down (C) key. Pressing the selection button (A) again takes you to the minutes display, which can be set in the same way.
Einstellen der Wurfweite
Press the selection button (A) 3 times to select the throw distance (E) and select the distance by pressing the up (B) or down (C) button. The indications correspond to the following distances:
S: Short distance of approx. 1 m
M: Medium range of approx. 2 m
L: Long range of approx. 3 m
Setting the feed time
Press the selection button (A) 4 times to go to the feed time display (J). Set the desired time by first selecting the hours with the up (B) or down (C) button and then entering the respective minutes after pressing the
selection button (A). This is the 1st feeding level (I); the digit 1 is displayed.
Setting the feed duration
Once you have set the feed time, press the selection button (A) again to go to the feed duration. The activity indicator (F) appears and you can choose from 0-20 seconds. No feeding starts at 0 seconds.
Setting the feed level
You can programme up to 6 feed levels (I). After you have programmed a feed level (I), you can move to the next feed level (I) by pressing the selection button (A) until, after the 6th level, you return to the current
time.
Manual feeding
If you press and hold the start button (D) for 3 seconds, manual feeding will also start for 3 seconds.
I
G
J
H
F
E
A
B
C
D
D
Device parts/ Scope of delivery
Designation
1 Cover
2 Solar panel
3 Feed bucket cover
4 Desiccant holder
5 Feed bucket
6 Screw 1
7 Feed wheel cover
8 Feed wheel
9 Screw 2
10 Lower part of the housing
11 Feed chute
12 Screw 3
13 Control panel with cover
14 Switch
15 Stand
16 Ground anchor
2. Installation on level ground
If the ground is hard and level, it is advisable to connect the stands to the ground
with screws and, if necessary, dowels (not included in the scope of delivery). To do
so, place the solar feeder on the appropriate surface and mark the fastening points
by marking drilling points through the holes in the stands (15). Set the solar feeder
aside and drill the marked holes to the appropriate depth. Mount the dowels, place
the solar feeder on the boreholes and screw the stands (15) with the screws.
F Activity indicator
Designation
A Selection button
G Battery charge indicator
B Up button
H Charge indicator
C Down button
I Feed level
D Start
J Feed time
E Throw distance
K Current time
11
2
3
1
4
5
6
7
8
9
10
13
11
12
14
15
16
