Tabla de contenido
Idiomas disponibles
Idiomas disponibles
EnGlish
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
nOTE: Do not attempt to mount CMCB101 charger under a
bench or table.
nOTE: Only mount CMCB101 charger with the charging
lights pointed upward toward the ceiling.
VersaTrack™
WARNING: Do not charge batteries while charger is
hung on Trackwall.
CRAFTSMAN chargers, except the CMCB101, can be
stored on CRAFTSMAN VersaTrack™ Trackwall. Hooks and
accessories are sold separately. Please refer to the VersaTrack™
Trackwall accessory sheet for further information.
nOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwall compatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Tool Specifications
Voltage
Output pressure
Flow rate
Grease type
Grease capacity
Bulk
Cartridge
Hose length
Weight (without battery pack)
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments, accessories or when filling
with grease. An accidental start‑up can cause injury.
LED Worklight (Fig. E)
CAUTION: Do not stare into the LED. Serious eye
injury could result.
When the tool is activated by pressing the trigger switch
the LED worklight
4
will automatically turn on. The LED
worklight will turn off 60 seconds after the trigger switch has
been released.
10
CMCGG001
V
20
Speed 1
10,000
psi
Speed 2
5,000
Speed 1
3
fl. oz./min
Speed 2
9
Up to NLGI #2
oz
16
oz
14.5
in
40
lbs
7.6
1
Variable Speed Trigger Switch (Fig. A, F)
Lock-Off Button and Trigger Switch
Your grease gun is equipped with a lock-off button
The lock-off button
either end to indicate if the trigger switch is locked or unlocked.
1. To lock the trigger switch
from the locked icon end as shown in Fig. F.
nOTE: Always lock the trigger switch
or storing the tool to eliminate unintentional starting.
2. To unlock the trigger switch
from the unlocked icon end as shown in Fig. F.
3. Squeeze the trigger switch
4. Releasing the trigger switch turns the motor OFF.
nOTE: The variable speed trigger switch will give you added
versatility. The further the trigger is depressed the higher the
output of grease.
WARNING: This tool has no provision to lock the
switch in the ON position, and should never be locked
ON by any other means.
Pressure Relief Valve (Fig. G)
The pressure relief valve
pressure above 10,000 PSI (690 bar). Grease coming out
of the pressure relief valve indicates a clog in the fitting,
line or bearing. Any of these conditions must be corrected
before proceeding.
WARNING: The grease gun may generate high
pressure. Do not remove or tamper with the
pressure relief valve. Serious injury may occur.
Installing a Grease Cartridge (Fig. A, I, G)
1. Pull the grease tube handle
then secure the grease tube rod
slot
14
by moving the rod to the side. Ensure the rod is
placed securely in the slot to prevent it from disengaging.
2. Unscrew the grease tube assembly
grease gun.
3. Remove the plastic cap from the grease cartridge, then
insert the cartridge, open end first, into the grease
tube
9
.
4. Remove the seal from the other end of the
grease cartridge.
5. Thread the grease tube assembly
grease gun and screw it in securely.
6. Release the grease tube rod
slot
14
and slowly press it back into the tube.
7. Use the purge valve (
that may be trapped in the cartridge. Refer to Purging
Air Pockets.
iMPORTAnT: The grease gun will lose its prime if there are
,
air pockets in the lubricant.
Removing Empty Grease Cartridge (Fig. I)
1. Pull the grease tube handle
then secure the grease tube rod
slot
14
by moving the rod to the side. Ensure the rod is
placed securely in the slot to prevent it from disengaging.
2
has a locked or unlocked icon at
1
, press the lock-off button
1
when carrying
1
, press the lock-off button
1
to turn the motor ON.
is set at the factory to relieve
22
11
out as far as it will go,
12
into the retaining
13
from the
13
back into the
12
from the retaining
23
, Fig. G) to bleed off any air
11
out as far as it will go,
12
into the retaining
2
.
2
Tabla de contenido
