Tools Needed; Safety Information; Need Help - Good Earth Lighting SE1249-BP2-02LF7-G Manual De Instrucciones

Step
Ladder
SHUT OFF POWER AT THE CIRCUIT BREAKER OR FUSE
PANEL BEFORE REMOVING THE OLD FIXTURE OR
READ ENTIRE INSTALLATION PROCEDURE BEFORE YOU BEGIN!
LIGHT FIXTURE REQUIRES A 120VAC
ELECTRICAL SYSTEM.
LIGHT MUST BE PROPERLY GROUNDED.
SOME REGIONAL/LOCAL CODES REQUIRE
INSTALLATION BY A QUALIFIED ELECTRICIAN.
WARNING!
This fixture can only be installed over a recessed
electrical box OR a UL-Listed surface mount electrical box
rated for wet locations. Surface mount electrical boxes require
the use of the included foam gasket, to prevent water from
seeping into the electrical box.
WARNING!
BURN HAZARD: Keep fixture's lamp heads at least 2 in.
from combustible material.
CAUTION!
BURN HAZARD: Allow light to cool down prior to
touching.
WARNING!
To avoid water damage, position light heads and sensor
head in the correct position as indicated.
ATTENTION
If the power goes out, the fixture will maintain previous
settings, so there is no need to go up the ladder to adjust once
the power has been restored.Fixture will need 20-30 seconds
to warm up once turned back on.
FCC STATEMENT:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not
expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the
separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that of the receiver. 4) Consult the dealer or an
experienced radio/TV technician for help. FCC responsible party name : Good Earth Lighting Inc. Address: 1400 E Business Center Drive, STE 108 Mount
Prospect, IL 60056 USA. Telephone number: 1-800-291-8838

Need Help?

Tools Needed

Silicone
Hammer
Seal

Safety Information

INSTALLING THE NEW ONE.
Please visit our website at: https://goodearthlighting.com/contact-us or call the
Customer Care Center 1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.
Phillips Head
Screwdriver
WARNING!
Do not look directly at the LEDs for an extended
period of time. They can cause eye damage.
CAUTION
Minimum 90°C supply conductors. For fixture
electrical ratings, see fixture label.
CAUTION
Please consult a qualified electrician if you are
unfamiliar with electrical installations, or methods of
properly grounding an electrical fixture.
CAUTION
Fixture will reliably operate between the
temperatures of -20°F to 122°F. (At temperatures above
92°F, the PIR may not detect body heat.)
WARNING!
The components of this fixture are not serviceable.
Attempting to alter the fixture for any reason may result in
voiding the warranty and could result in creating a
dangerous situation.
ATTENTION
LEDs can be damaged by electrostatic discharge
shock. To remove this hazard, touch a grounded bare
metal surface to discharge yourself before installation.
Work
Safety Glasses
Gloves
3