Tabla de contenido
Idiomas disponibles
Idiomas disponibles
English
Battery liquid may be flammable if exposed to spark
•
or flame.
•
Never attempt to open the tool for any reason. If the
tool case is cracked or damaged, do not charge. Do
not crush, drop or damage the tool. Do not use a tool or
charger that has received a sharp blow, been dropped, run
over or damaged in any way (e.g., pierced with a nail, hit
with a hammer, stepped on). Damaged tools should be
returned to the service center for recycling.
Storage Recommendations
The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold. Store the fully
charged tool disconnected from the charger cable.
Transportation
nOTE: Integral Li‑ion tools should not be put in checked
baggage on airplanes and must be properly protected from
short circuits if they are in carry‑on baggage.
Tool Disposal
This product uses a lithium‑ion rechargeable and recyclable
battery. When the battery no longer holds a charge, the tool
should be recycled. The tool should not be incinerated or
placed in the trash.
The tool can be taken for disposal to an Authorized Service
Center. Some local retailers are also participating in a national
recycling program (refer to RBRC®). Call your local retailer for
details. If you bring the tool to an Authorized Service Center,
the Center will arrange to recycle the tool and its battery.
Or, contact your local municipality for proper disposal
instructions in your city/town.
Important Safety Instructions for All
Integral Battery Charging
WARNING: Read all safety warnings, instructions,
and cautionary markings for the battery, charger
and product. Failure to follow the warnings and
instructions may result in electric shock, fire and/
or serious injury.
The provided charger is not intended for any uses
•
other than charging BLACK+DECKER rechargeable
tools. Charging other types of tools may cause
their batteries to overheat and burst, resulting in
personal injury, property damage, fire, electric shock
or electrocution.
•
DO NOT expose charger to water, rain or snow.
Pull by the plugs rather than the cord when
•
disconnecting the charger. This will reduce the risk of
damage to the plugs and cord.
•
Make sure that the cord is located so that it will not
be stepped on, tripped over or otherwise subjected to
damage or stress.
When charging the tool outdoors, always provide a
•
dry location.
•
DO NOT use a charger with a damaged cord or plugs.
Have them replaced immediately.
6
Foreign materials of a conductive nature, such as, but
•
not limited to, grinding dust, metal chips, steel wool,
aluminum foil or any buildup of metallic particles
should be kept away from the charger and charging
contacts.
Always unplug the charger from the power supply
•
when there is no tool attached to it.
Charging the Battery (Fig. A, B)
WARNING: For use only with the supplied charger.
WARNING: Do not charge the battery at ambient
temperatures below 39 °F (4 °C) or above 104 °F (40 °C).
From new, the rechargeable cells of the product need a
minimum charge time of 3 to 4 hours to ensure full power.
1. The switch must be in the OFF position, the tool will not
charge if it is in any other position.
2. Fig. B ‑ Plug the jack plug
charging socket
6
of the tool.
3. Plug the charger
3
into any standard 120 Volt 60 Hz
electrical outlet.
4. The charge indicator LED
housing
9
will illuminate while charging.
5. The charge indicator LED
completion of charging.
nOTE: While charging, the charger may get warm,
this is perfectly normal and safe. It is safe to leave the
appliance connected to the charger indefinitely. The
charger automatically reduces power consumption when
charging is complete.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and keep hands away from
the switch before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Attaching Hook and Loop Sanding Discs
(Fig. C)
Your sander is designed to use 3 3/8" (85mm) sanding discs.
Sanding discs attach with hook and loop.
1. To attach the sanding disc
sanding pad
5
and press the disc firmly in place.
2. The hook and loop fastening system sanding disc can be
easily removed by simply pulling it off. It can be reused
as desired.
nOTE: These sanders are not to be used in drywall
applications. Using a sanding screen (e.g., screen used for
sanding drywall) directly on the hook and loop pad will not
hold and will damage the hooks on the pad. The hooks on
the pad will wear very rapidly if left in contact with the work
surface while the tool is operating.
8
of the charger into the
7
on the center of the main
7
will turn off upon
4
, carefully center it over the
Tabla de contenido
