EINHELL TE-CD 18/48 Li-i Manual De Instrucciones página 12

6. Operation
6.1 Torque setting (Fig. 2/Item 1)
Caution! Only ever adjust the torque setting
ring when the equipment is at a standstill.
The cordless hammer drill driver is fi tted with a
mechanical torque selector.
The torque for a particular screw size is set with
the setting ring (1). The torque is dependent on a
number of factors:
•
On the type and hardness of the material
involved.
•
On the type and length of the screws used.
•
On the requirements that the screw
connection has to satisfy.
The tool will stop rotating as soon as the set
torque is reached during operation
6.2 Selector switch for driving/drilling/impact
drilling (Fig. 2/Item 13)
•
For driving purposes, set the selector switch
(13) to the "Screw" position. The torque is
adjusted via the torque setting (1) (see point
6.1).
•
For drilling purposes, set the selector switch
(13) to the "Bit" position. The slip coupling is
now off and the maximum torque is available
regardless of the torque setting (1).
•
For impact drilling purposes, set the selector
switch (13) to the "Hammer" position. The slip
coupling is now off and the maximum torque
is available regardless of the torque setting
(1).
Important! Change the torque setting (1) and
the selector switch for driving/drilling/impact
drilling (13) only when the equipment is at a
standstill.
6.3 Changeover switch (Fig. 3/Item 3)
The slide switch above the On/Off switch is for
setting the direction of rotation of the cordless
hammer drill driver and for preventing the
cordless hammer drill driver from being switched
on inadvertently. You can select between
clockwise and counter-clockwise rotation.
To avoid causing damage to the gearing, the
direction of rotation must only be changed when
the equipment is at a standstill. When the slide
switch is in the middle position, the On/Off switch
is locked.
Anl_TE_CD_18_48_Li_i_SPK7_USA.indb 12 Anl_TE_CD_18_48_Li_i_SPK7_USA.indb 12
EN
6.4 On/Off switch (Fig. 3/Item 4)
Infi nitely variable speed control is possible with
the On/Off switch. The further you pull the switch,
the higher the speed of the cordless hammer drill
driver.
6.5 Switching from speed 1 to speed 2
(Fig. 2/Item 6)
You can work with a higher or lower speed
depending on the position of the selector switch.
Change the gear only when the drill is at a
standstill. If you fail to observe this point, the
gearing may be damaged.
6.6 Battery capacity indicator (Fig. 4 / item 2)
Press the battery capacity indicator switch (12).
The battery capacity indicator (2) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The temperature of the battery is too low. Remove
the battery from the device and leave it at room
temperature for a day. If the error occurs again,
this means that the battery has been completely
depth-discharged and is defective. Remove the
battery from the device. Never use or charge a
defective battery.
6.7 LED lamp (Fig. 4/Item 9)
The LED light (9) can be used in poor lighting
conditions to illuminate the area where you want
to drill or screw. The LED light (9) will come on
automatically as soon as you press the On/Off
switch (4).
6.8 Changing the bit (Fig. 5)
Caution! Set the changeover switch (3) to its
center position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the cordless hammer drill driver.
•
The cordless hammer drill driver is fitted with
a quick-action chuck (8) with an automatic
spindle stop.
•
Open the chuck (8). The chuck opening (11)
must be large enough to hold the tool (drill bit
or screwdriver bit).
- 12 -
03.05.2022 12:57:09 03.05.2022 12:57:09