Idiomas disponibles
Idiomas disponibles
PHI
A
All manuals and user guides at all-guides.com
bus (usually the one with terminals B IN not connected).
2 - Remove jumper SW1.
3 - Wait for the note confirming the operation (approxi-
mately 3÷15 s).
The number of confirmation signals also indicates the
number of present and programmed entry panels (1
signal for the main entry panel and 1 signal for each sec-
ondary entry panel).
4 - Refit jumper SW1.
Programming receivers
1 - Remove jumper SW2 from any entry panel.
2 - Lift the handset of the receiver to be programmed (for tel-
ephone sets, see the instructions featured in interface IT/300).
3 - Press the door-lock release and auxiliary 2 buttons at
the same time for at least 1 s (when audio towards the
entry panel is enabled, the operation is confirmed).
4 - On the entry panel, press the call button the receiver
is to be associated with.
5 - Replace the handset.
6 - Repeat the operation from point 2 on for all remaining
receivers.
6
7 - Refit jumper SW2 to exit programming.
WARNING. The programming procedure for the
VSE/301 selector, where fitted, must only be per-
formed once you have programmed which calls
from the entry panels are to be associated with
which receivers. In installations with XA/300LR
we recommend you gather up the receiver's ID
(SN) codes, applied on the outside of the housing,
and enter them in the tables that come with the
XA/300LR and IPC/300LR.
NOTE. Once the power supplier has been programmed
using a PCS/300 unit, it will no longer be possible to
gain access to the entry panel standard programming.
To restore default conditions, please refer to the
related chapter.
Return to default conditions from entry panel
1 - Remove the SW1 jumper.
2 - Close the earthed door open contact (–,
A sound signal confirms that the operation has occurred.
3 - Replace the SW1 jumper
COLOUR VIDEO ENTRY PANEL HEVC/301
7
Video entry panel complete with colour CCD camera and
white-light LED for lighting the target area.
Its features and functions are similar to those of entry
panel HEV/301.
Technical features
• Power supply:
14÷18 V DC.
• Current demand:
- on stand-by with 14V DC max. 230 mA;
- operating with 14V DC max. 380 mA;
- with door-lock release activated, add 500 mA;
- for each HEP/306-HEP/312D, add 35 mA;
- for each XDV/300A connected, add 40 mA;
- for 64 receivers, add 64 mA.
• Secrecy of speech/privacy of video signal.
• Door-lock release command: pulse-type for solenoid
lock at 12 V 1 A.
• Timed solenoid door-lock release: adjustable in the
range 1 to 15 s.
• Installation activation time: 60 s.
• Call duration time: 30 s.
• Bus output: power supply at 15 V DC for booster and
receivers video driver balanced type (Z = 100 Ω).
• Aux 1 command output: 3.5 V DC at 1 mA (available
8
only with entry panel enabled, activation time same as
timed solenoid door-lock release).
• Aux 2 command output: 3.5 V DC at 1 mA (always avail-
able in all entry panels, activation time same as timed
solenoid door-lock release).
• Entry panel activation output: 3.5 V DC at 1 mA (ena-
bled for entire duration of conversation).
• Working temperature range: -15 °C to +50 °C.
Camera technical features of HEV/301 entry panel
• Video signal system: CCIR (EIA).
• Sensor: 1/4" CCD.
• Horizontal frequency: 15,625 Hz (15,750 Hz EIA).
• Vertical frequency: 50 Hz (60 Hz EIA).
• Video output: 1 Vpp composite to 75 Ω.
• Resolution: 380 lines.
• Minimum illumination: 5 lx.
• S/N ratio: 45 dB.
• Iris control: automatic electronic in the range 1/50 s
1/100,000 s.
• Lens: fixed-focus f 3.7 F 4.5.
Camera technical features of HEVC/301 entry panel
• Video signal system: NTSC.
• Sensor: 1/4" CCD.
9
• Horizontal frequency: 15,625 Hz.
• Vertical frequency: 50 Hz.
• Video output: 1 Vpp composite to 75 Ω.
• Resolution: 330 lines.
• Minimum illumination: 50 lx.
• S/N ratio: 46 dB.
• Iris control: automatic electronic.
• Lens: fixed-focus f 3.7 F 5 (pin-hole).
INSTALLATION
YKP/301+YV(YVC) monitor with handset
WARNING. It is recommended to install the monitor
in a dry place.
Remove the monitor module by using a screwdriver in
the slot of the housing (fig. 2).
Remove the connector shown in figure 3.
The wall mounting can be installed following the instruc-
tions in figures 4-8. Fit the monitor module on the wall
mounting as illustrated in figures 9 and 10. To remove the
YKP cover, use a screwdriver inserted in the slot (fig. 7).
Video entry panel HEV/301-HEVC/301
The embedding box must be fitted flush with the wall
and at an height that ensure optimal camera operation.
Fit the spacer into embedding boxes to avoid deforma-
tion (fig. 12). It is possible to use the screwdriver obtained
from the spacer to adjust the microphone and speaker
volume (fig. 15).
WARNING. Connecting cables must be fed through one
of the knockout cable entry points, located at the bot-
tom of the embedding box (A in fig. 12).
Using the Allenkey s 2.5 supplied, unscrew the lock screw
and remove the front plate from the chassis (fig. 13).
In order to fit additional buttons, follow the instructions
supplied with each. Remove the two plugs protecting
the threaded holes in the embedding box and secure the
chassis using the two screws supplied (fig. 14).
Perform the wiring. The name card can be removed and
filled in with the relevant information by removing the card
clip followed by the actual card itself (fig. 18).
NOTE. Personalized name cards can be used up to a maxi-
).
mum of 2 mm thick.
In order to fit the front plate, first insert the upper part in
the top moulding and then, using a Allenkey s 2.5, tighten
the lock screw (fig. 19).
DISPOSAL
Do not litter the environment with packing material: make
sure it is disposed of according to the regulations in force
in the country where the product is used.
When the equipment reaches the end of its life cycle, take
measures to ensure it is not discarded in the environment.
The equipment must be disposed of in compliance with
the regulations in force, recycling its component parts
wherever possible.
Components that qualify as recyclable waste feature the
relevant symbol and the material's abbreviation.
LEVITON
LEVITON S de RL de CV
LAGO TANA 43 Col HUICHAPAN CP 11290
MEXICO DF Tel 5082 1040
LEA Y CONSERVE ESTE
INSTRUCTIVO
INSTRUCCIONES PARA
E
LA UTILIZACIÓN Y INSTALACIÓN
ADVERTENCIA AL INSTALADOR
Estas instrucciones se deben anexar al aparato.
SOPORTE DE PARED YKP/301 CON AURICULAR
Este soporte está preparado para el montaje del módulo
monitor YV o YVC y de las unidades YP3 e YPL en la insta-
lacion Sistema X1.
También es posible montar el altavoz YAL, si fuese nece-
sario aumentar la nota de llamada.
VIDEOINTERCOMUNICADOR CON TELÉFONO
YKP/301+YV
Derivado interno compatible con el sistema X1 (alimenta-
ción integrada en el BUS).
Dispone de los siguientes comandos (fig. 1):
Abrepuerta (
)
1
Habilitación y selección placa exterior (
Auxiliar 1 (
)
1
)
2
3
