VONROC S CS503AC Traducción Del Manual Original página 11

Mounting the handle (Fig. B-2)
• Mount the handle (2) to the metal part on the
support plate (16) as shown in Fig. B-1.
• Fix the Cap nut (20) tightly using a wrench.
Mounting the dust extraction pipe (Fig. B-3)
• Mount the dust extraction pipe (8) using the
15mm hex bolt (21) as shown in Fig. B-3.
When mounting the saw blade, wear
protective gloves. Danger of injury when
touching the saw blade.
Only use saw blades that correspond with
the characteristic data given in the
operating instructions.
Do not under any circumstances use
grinding discs as the cutting tool.
Blade replacement without removing the guard
(Fig. D)
• Press the spindle lock button (24) to prevent
the saw from turning. (Fig. D-1)
• Keep the spindle lock button (24) pressed and
loosen the clamping nut (26) using the hex key
(19). (Fig. D-2)
• Remove the mounting flange (25).
• Loosen the saw depth limiter (3) using the hex
key (19) and press the guard to remove the
blade. (Fig. D-3)
• Keep the guard pressed and place the new bla-
de onto the blade shaft. Ensure the hole locates
correctly and the teeth point in the direction of
the curved arrow. (Fig. D-3)
• Place the mounting flange (25) insuring the
long sides of the mounting flange correspond
with the long sides of the blade shaft.
• Press the spindle lock button (24) pressed and
tighten the clamping nut (26) using the hex key
(19). (Fig. D-4)
• Make sure the blade rotates smoothly by rota-
ting the sawblade at least one turn. Check if the
guard functions correctly.
Attaching the parallel guide (Fig. C)
• Attach the parallel guide (22) on the right side
of the machine, as shown in Fig. C-1.
• Lock the guide down by turning the adjustment
knob (23) clockwise.
WWW.VONROC.COM
Assembling the guide rail (Fig. A, F)
• Slide the saw coupling bar (12) into the groove
on the guide guide rail (11).
• Position the coupling bar exactly in-between
the two guide rails as shown in figure F-1.
• Tighten the grub screws on the coupling bar,
fixating the two guide rails.
• Slide a clamp (13) into each of the two grooves
on the guide rail (11).
• Firmly tighten the clamp onto the workpie-
ce. Make sure both clamps are always firmly
mounted and tightened onto the workpiece and
a surface (table).
• Make sure the rail guide (14) retains a good
grip onto the guide rail (11) when using the
saw, as shown in figure F-3.
4. OPERATION
Switching the machine on/off (Fig. A)
• Slide the on-/off switch (4) forward.
• Release the on-/off switch to switch the machine
off.
Adjusting the cutting depth (Fig. E)
• Loosen the saw depth limiter (3) using the hex
key (19) and move the saw depth limiter to the
required saw depth. The sawing depth 'A' is
shown in Fig. E-2.
• Tighten the saw depth limiter (3) using the hex
key (19).
Speed adjustment (Fig. A)
The required speed can be adjusted by using the
Speed adjustment knob (7). Also during running
the rotational speed can be adjusted.
• To increase the speed, turn the Speed adjust-
ment knob (7) clockwise.
• To decrease the speed, turn the Speed adjust-
ment knob (7) anti-clockwise.
The required speed depends on the material and
can be determined by practical testing.
Optimum use
• For optimal result when sawing wood, the cut-
ting depth should be set slightly greater than the
thickness of the chosen material.
• When cutting plastic, the cutting depth should
also be greater than the thickness of the material.
If the material begins to melt, then setting a grea-
ter depth of cut usually resolves the problem.
EN
11