Tabla de contenido
Idiomas disponibles
Idiomas disponibles
gb
This manual is consistent with the date of manufacture of
your machine, you will find information on the technical
data of the machine acquired manual check for updates
of our machines on the website:
www.grupostayer.com
1_MACHINE SPECIFIC SAFETY
WARNINGS
Keep your whole body away from the saw when it
is in operation. Before operating the saw make sure
that the chain is not in contact with anything.
Keep the handles dry and free of moisture and oil. A
slippery handle can lead to accidents.
Always hold the tool with both hands, placing one
hand on the main handle controlling the trigger while
the other hand holds the auxiliary handle. Holding
the tool with only one hand or incorrectly can lead to
accidents.
Always hold the tool by the rubber areas. The saw
could cut a hidden cable and cause an electric shock
to the operator.
Switch off the power tool immediately if it becomes
jammed.
Whenever possible clamp the workpiece with clamps
or clamp clamps. Holding the workpiece by hand or
against the body can cause accidents.
Always maintain a firm and safe working posture.
Using the tool in awkward positions can cause accidents.
Make safe cuts by resting the saw on the tool's
support point.
Do not attempt to cut anything until the machine is
switched on and running at full power. If the tool is
operated while in contact with any material, the chain
may bounce or jam causing accidents.
When you have completed a cut, turn the tool off and
do not remove it from the material until it has come
to a complete stop. This way you can avoid bouncing
and kickback.
Only use chains and bars that are in perfect condition.
The use of dull or damaged chains can affect the quality
of the cut and cause accidents.
Do not brake the saw by applying excessive pressure
to the cut or by pressing sideways against the cutting
material. This could damage the tool and break the chain
causing accidents.
Use skin, eye and respiratory protection.
Avoid kickback, kickback and jamming. These
incidents occur when touching any material with the
tip of the saw in operation, or while making a cut in
wood where the cut is constricted by the weight of
the workpiece trapping the chain. When the tool is
subjected to this type of situation, the tool can bounce
violently against the material, become jammed or
cause a kickback that pushes the tool against the
operator.
All of these situations pose a risk to the operator,
so extreme caution must be exercised and all safety
precautions in this instruction manual must be
followed:
- Maintain a firm grip, keeping fingers and other body
parts away from the chain. Holding the tool firmly allows
you to control it in the event of kickback or recoil.
- Do not cut in awkward, unstable, stretched or over-
shouldered positions to avoid unintentional contact
with the tool tip.
- Use only manufacturer's approved replacement
parts.
- Keep the chain sharp and all components well
maintained and cared for.
- Before starting work ensure that the chain is in
good condition, correctly tensioned, lubricated and
fitted to the bar, with all components securely locked
into position.
BATTERIES USE AND CARE
Do not open the battery. Danger of shortcircuiting.
Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints. The vapours can
irritate the respiratory system.
Use the battery only in conjunction with your STAYER
power tool. This measure alone protects the battery
against dangerous overload.
Use only original STAYER batteries with the voltage
listed on the nameplate of your power tool. When using
other batteries, e. g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The battery
can be damaged.
The battery is equipped with a temperature control
which allows charging only within a temperature range
of between 0 °C and 45 °C. A long battery service life is
achieved in this manner.
Observe the notes for disposal.
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the
first time.
The lithiumion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
The lithiumion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The inserted
tool no longer rotates.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be
subject to overload. When the load is too high or the
allowable battery temperature range of 0–50 °C is
exceeded, the speed is reduced. The power tool will
not run at full speed until reaching the allowable battery
temperature. position. Unintentional actuation of the On/
Off switch can lead to injuries.
Open the keyless chuck 2 by turning in rotation direction ,
until the tool can be inserted. Insert the tool. Firmly tighten
the collar of the keyless chuck 2 by hand in rotation
-
12
-
Tabla de contenido
