Tabla de contenido
Idiomas disponibles
Idiomas disponibles
EN
water pipes in the area where the heater is to
be installed.
1. Start by mounting the lower tube (10) onto the
baseplate (12). Tighten the long bolts (13) as
shown on figure B.
2. Slide the cover (11) onto the lower tube (10) as
shown on figure B. This will hide the bolts (13)
from plain sight.
3. Take a large cable holder (9) and put it on the
middle tube (8) as shown in figure C.
4. Now put the middle tube (8) onto the lower
tube (10). Ensure the holes in both tubes align.
Now tighten with the short bolts (14) as shown
in figure C.
5. Take a large cable holder (9) and put it on the
upper tube (6) as shown in figure D.
6. Now put the upper tube (6) onto the middle
tube (18). Ensure the holes in both tubes align.
Now tighten with the short bolts (14) as shown
in figure D.
7. Untighten the clamping ring (15) on the upper
tube (6) by turning it anti-clockwise. Now, the
extendable tube (16) can be extended upwards
by pulling it.
8. When the desired height is reached, righten
the clamping ring (15) on the upper tube (6) by
turning it clockwise.
9. Take the small cable holder (7) and put it on the
extendable tube (16) as shown in figure D.
10. Slide the hole on the underside of the heater
(1) onto the extendable tube (16) as shown on
figure E.
11. Ensure the two holes in the the heater (1) align
with the holes in the extendable tube (16).
4. OPERATION
Switching on/off (Fig. A)
The heater can be turned on and off using the pull
cord. Pull the cord of the pull switch (5) until the
desired heating level appears on the heating level
indicator (3):
• Level 0 = switched off
• Level 1 = 730W
• Level 2 = 1460W
• Level 3 = 2200W
To turn the heater off, pull the cord of the pull
switch (5) to the 0 level position.
8
Tip over safety switch (Fig. A)
This heater is fitted with a tip-over safety switch. In
the event that the heater falls over, the heater auto-
matically shuts off. Please note that when the heater
is returned to its upright position, it does not resume
its operating immediately. First switch it off (read
'switching on/off'), remove the plug from the socket
and check the heater for damage. In case of damage
or malfunctioning do not use but offer for checking /
repair. If there is no damage, you can simply switch
the heater on again (read 'switching on/off').
5. MAINTENANCE
Always make sure that the machine is not
connected to the mains electricity when you
carry out any maintenance of the mechanism.
CAUTION: Risk of Electric Shock. DO NOT
open or try to repair the heater yourself.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that the
ventilation openings are free of dust and dirt. Re-
move very persistent dirt using a soft cloth mois-
tened with soapsuds. Do not use any solvents such
as gasoline, alcohol, ammonia, etc. Chemicals such
as these will damage the synthetic components.
• DO NOT use alcohol, gasoline, abrasive pow-
ders, furniture polish or rough brushes to clean
the heater. This may cause damage or deterio-
ration to the surface of the heater.
• DO NOT immerse the heater in water.
• Wait until the heater is completely dry before
use.
ATTENTION:
1. Always disconnect the heater from the electric-
ity supply and allow it to cool before attempting
to clean it.
2. If the heater has collected dust or dirt inside
the unit or around the heating element, have to
unit cleaned by a qualified service agent. Do not
operate the heater in this condition.
3. The only maintenance required is cleaning of
the external surfaces of the heater.
4. Do not touch the heating element with bare
fingers, as residue from your hand could affect
the life of the lamp. If it is accidentally touched,
remove the finger marks with a soft cloth mois-
WWW.VONROC.COM
Tabla de contenido
