stayer SCC 315 Manual De Instrucciones página 16

This manual is consistent with the date of manufacture of your
machine, you will find information on the technical data of the
machine acquired manual check for updates of our machines
on the website:
www.grupostayer.com
PROVIDED USES OF THE MACHINE
1.
This tool has been solely and exclusively provided for:
1 Stationary works on flat and stable surface
2 Working on hard and soft wooden pieces
3 Working on chipboard pieces
4 Working on fiberboard pieces
5 Working on PVC tubes
6 Making rectilinear cuts along the length and width of the
workpiece
7 Making horizontal mitre-cuts between -45º and 45º.
8 Making vertical mitre-cuts between 90º and 45º
Refer to the limits regarding the size of the workpiece in
corresponding chapter 11.
UNPACKAGING AND ASSEMBLING
2.
Unpackaging
1 Cut the seal and open the box.
2 Withdraw upper cardboard stoppers
3 Extract the box by firmly grasping the operating head and
the motor body using both hands so as to balance the
weight.
4 Extract the box with the accessories
5 Extract the documentation
6 Preserve the cardboard box, the stoppers there of and
the documentation permanently in an inventoried safe
environment being easily accessible and known to the
machine operator.
Packaging
Operation 1: Securing, folding and fastening the
operating head:
1 Place upper head at horizontally 0º.
2 Place upper head at vertically 90º.
3 Arrange protector such that it contacts the cutting bench.
4 Lower head to the limit and position it to be able to lock it.
5 Push lower locking button to lock the head.
Operation 2: Packaging the machine
1 Locate the cardboard box.
2 Locate documentation.
3 Firmly grasp the machine by its operating head and
motor body.
4 Place the machine over the 4 circular recesses of the
bottom of the box.
5
Store documentation of the machine.
6
Position upper cardboard stoppers.
7
Close the box and fix it with sealing tape.
SETTING OR FASTENING THE MACHINE IN A STABLE
3.
POSITION
1
The working area where the machine is being arranged
must mandatorily be safe.
2
Support tool in a stable position on an even surface.
3
The base of the mitre saw has four holes for firmly
fastening the machine to the working bench. It is strongly
recommended to fix the machine to the bench by means
of the pertinent screws and nuts.
CONNECTION TO THE GRID, WIRING, FUSES,
4.
SOCKET TYPE FOR THE JACK AND REQUIREMENTS
FOR GROUNDING
1
For supplying electrical power to the machine, connect the
ENGLISH
16
Schuko Jack to a standard socket capable of supplying a
minimum of 2500 VA .
2
The internal wiring of the machine is completely
terminated so that no wiring is needed when installing it.
3 The machine does not have fuses although the use of a
dedicated magnetothermal switch is recommended as a
protection for the machine.
4 The machine has a class II electrical equipment so that
it does not make use of the grounding of the electrical
installation.
ILLUSTRATED DESCRIPTION OF THE FUNCTIONS
5.
1 Angle selector knob (mitre).
2 Lower table guard when using the upper table.
3 Head unlocking button.
4 Height adjusters for upper table.
4 a) Locking screws
5 Pin for locking head in the down position.
6 Blade lowering stopper.
7 Blade tilt adjustment screws 0° / 45°.
8 Head tilt knob (bevel).
9 Bracket slot for long cuts (SCC315W).
10 Slot for clamps.
11 Blade locking lever
12 Mitre saw switch / lower table
13 ON/OFF interlock switches on upper table.
14 Safety lock for use on lower table
15 Safety lock when using upper table.
16 Lateral guide / Upper table guard
17 Upper table blade guard
A Lower table with degree scale ruler
B Upper table and upper blade guard
C Head pivot axes
D Lower blade guard
E Outlet for connection to dust collector
F Head
G Grip and motor
H Extendible bracket for large workpieces SCC315 (x2)
LIMITATIONS REGARDING ENVIRONMENTAL
6.
CONDITIONS
The IP degree of this machine is 20. This machine is protected
against its dangerous parts being accessed by a finger and
against solid foreign particles having diameters of 12'5 mm
and more.
This machine does not have any kind of protection against the
entry of water so that its use in exterior or interior environmental
conditions with a risk of precipitations is forbidden.
SETTINGS AND TESTING
7.
Warning!
Before any intervention on the electrical tool remove jack
from power socket.
If the machine has been subject to prolonged or intense use, it
must be checked and adjusted so as to ensure the machine's
correct quality of service and safety.
This requires knowledge, experience and special tools. The
official technical service of Stayer Iberica S.A. will carry out
that work for you in a quick thorough and inexpensive manner.
Locking in the down position
Verification
1 Start with the head raised.
2 Unlock the head by pressing on button 3.
3 Lower the head to the lowest position.
4 4. Pull the pin (5), turn it 90º and reinsert it in its slot. If
properly adjusted, the pin should go in smoothly until it
stops, leaving the head locked in place. If the pin does
not fit:
Adjusting
16