VONROC CS502AC Traducción Del Manual Original página 9

For replacing the saw blade, it is best to set the
depth to 0mm and set the bevel angle to 0°.
Afterwards, the machine can be placed on its side,
resting on the motor housing and baseplate.
Removing the saw blade
1. Press and hold the spindle lock (19) button.
2. Loosen the clamping bolt (15) using the hex key
provided, turning in anti-clockwise direction.
3. Remove the clamping bolt (15) and clamping
flange (16).
4. Retract the lower guard (14) by using the lever
(12) and remove the saw blade.
Mounting the saw blade
1. Clean the saw blade and all clamping parts to
be assembled.
2. Retract the lower guard (14) by using the lever
(12) and mount the saw blade. Ensure the
arrow on the saw blade corresponds with the
arrow on the lower guard (14).
3. Mount the clamping flange (16). Ensure the
flat sides of the clamping flange correspond
with the flat sides of the blade shaft. Also make
sure the convex side of the clamping flange is
mounted to the outside.
4. Press and hold the spindle lock (19) button.
5. Mount the clamping bolt (15) using the hex key
provided, turning in clockwise direction.
Attaching the parallel guide (Fig. D)
1. Loosen the clamping bolt for parallel guide (10)
2. Mount the parallel guide (22) onto the basepla-
te (17).
3. Set the desired cutting width using the scale
on the parallel guide (22) and the cutting mark
on the baseplate (17). The 45° cutting mark (8)
indicates the position of the saw blade for 45°
angled cuts. The 0° cutting mark (9) indicates the
position of the saw blade for right-angled cuts.
4. Tighten the clamping bolt (10).
4. OPERATION
Switching the machine on/off (Fig. A, B)
• To start the machine, press and hold the lock-
off button (3) and press the on/off switch (2).
• To stop the machine, release the on/off switch
(2).
WWW.VONROC.COM
Adjusting the bevel angle (Fig. A, B)
The 0° cutting mark (9) indicates the position of the
saw blade for straight cuts. The 45° cutting mark
(8) indicates the position of the saw blade for 45°
cuts.
1. Loosen the clamping bolt (7)
2. Adjust the baseplate (17) to the desired posi-
tion (0°- 45°). The sawing angle (bevel) can be
read on the scale (6).
3. Tighten the clamping bolt (7).
Adjusting the cutting depth (Fig. C)
1. Loosen cut depth clamping lever (20).
2. Move the baseplate (17) to the desired position.
The sawing depth) can be read on the scale (21).
3. Tighten cut depth clamping lever (20).
Optimum use
• Hold the work using clamps or a vice to have
both hands free to operate the saw.
• Switch on the saw and place the bottom plate
on the work.
• Slowly move the saw towards the previously dra-
wn cutting line and slowly press the tool forward.
• Firmly press the bottom plate on the work,
otherwise the circular saw may start to vibrate,
causing the blade to break more easily.
• Let the saw do the job. Do not put undue pres-
sure on the circular saw.
5. MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
mains plug from the mains.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that the
ventilation openings are free of dust and dirt. Re-
move very persistent dirt using a soft cloth moiste-
ned with soapsuds. Do not use any solvents such
as gasoline, alcohol, ammonia, etc. Chemicals such
as these will damage the synthetic components.
EN
9