Hozelock KILLASPRAY Manual De Instrucciones página 6

33795 KillaSpray12-16 Inst
Maintenance • Entretien • Onderhoud • Mantenimiento • Underhåll • Wartung • Vedlikehold • Huolto
Vedligehold • Manutenzione • Manutenção • Konserwacja • Συντήρηση • Bakım • Karbantartás • Údrãba
23
A
G
GB
k s
illa pray
Instructions & Warnings
• This sprayer is intended for use with water-based solutions of:
insecticides, fungicides, weedkillers & fertilizers.
• Always follow the chemical suppliers instructions, as well as
the instructions supplied with this sprayer.
Always wear protective clothing, goggles, face mask and
gloves.
Avoid inhaling spray mist.
Avoid skin contact with chemicals.
Always work in a well ventilated area.
Take care to protect children pets & fish from exposure to
chemicals.
Always wash hands thoroughly after use & especially before
eating.
Always wash any contaminated clothing.
Seek medical attention if spray gets in your eyes or you
develop any symptoms after spraying.
Do not spray near food or food preparation areas. When
spraying crops, pay particular attention to the chemical
manufacturers advice on time before crops can be eaten.
Do not spray any solvent e.g. White spirit.
Spray only thin watery solutions; thicker mixtures will clog
the nozzle.
Powdered chemicals can be sprayed successfully if they are
completely soluble in water. If they are not, or the solution
tends to settle, spraying can still be successful if the mixture
is continually agitated.
If the material to be sprayed contains sediment, strain the
liquid into the sprayer bottle.
Occasionally the pump will require lubrication.
First depressurise the system by squeezing the trigger.
Winter Use – drain liquid from all parts and prevent damage
from freezing.
5/12/07 18:24 Page 6
Обслуживание • Hooldus • Apkope • Remontas
24
A
G
A
25
H
B
D
C
Annual Maintenance – At least once per year thoroughly
clean the whole sprayer and apply silicone grease to all
moving parts & seals. Test with water, and if any washer or
seal has perished it must be replaced.
Notes
A Make sure all nuts are screwed hand tight before use.
B This sprayer is made from many different types of plastic,
and although the liquid you wish to spray may be packed in
plastic, this does not guarantee it will not damage the sprayer.
If you have any doubt about compatibility contact Hozelock
customer services. When filling the sprayer ensure that the
maximum fill level is not exceeded.
C
Ensure that the pump is screwed into the bottle tightly.
D If the sprayer has been used with chemicals, discard safely any
unused solution after use.
F Fill sprayer with warm water (not hot), re-assemble the sprayer
and spray some of the contents. Repeat; check that the nozzle
is free from sediment. If necessary repeat the process until the
sprayer is clean. NB : Do not use detergent.
Occasionally the pump will require lubrication.
First depressurise the system by squeezing the trigger.
G The pump O-ring should be lubricated to allow the sprayer to
pump air efficiently. Apply silicone grease regularly, to the
pump O-Ring (A).
H
The nozzle cap (B) & swirl grooves (C) should be kept clean
and free of obstruction. The O-ring should be lubricated to
allow the spray pattern to be easily changed. Apply silicone
grease regularly, to the nozzle O-ring (D).
I
Keep the trigger clean and free from build up of sediment and
chemicals by regularly flushing after use. If necessary remove
and clean the filter in the trigger.
Guarantee
• Hozelock guarantees this sprayer against any defect arising
from faulty materials or workmanship for a period of 3 years
from the date of purchase, provided that it has only been used
in accordance with these instructions. The guarantee is limited
to the repair or replacement of any defective or faulty item.
Proof of purchase must be retained.
26
I