GWARANCJA I SERWIS
Warunki gwarancji oraz opis postepowania w przypadku reklamacji
zawarte są w załączonej Karcie Gwarancyjnej.
Serwis Centralny
GTX Service
Ul. Pograniczna 2/4
02-285 Warszawa
Sieć
Punktów
Serwisowych
i
pogwarancyjnych
dostępna
gtxservice.pl
Grupa Topex zapewnia dostępność części zamiennych oraz materiałów
eksploatacyjnych dla urządzeń i elektronarzędzi.
Pełna oferta części i usług na gtxservice.pl. Zeskanuj kod QR i wejdź:
tel. +48 22 573 03 85
fax. +48 22 573 03 83
e-mail [email protected]
do
napraw
gwarancyjnych
na
platformie
internetowej
GB
TRANSLATION OF THE ORIGINAL INSTRUCTION
ANGLE GRINDER
51G075
NOTE: BEFORE THE POWER TOOL IS USED FOR THE FIRST TIME, READ
THIS INSTRUCTION MANUAL AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
ANGLE GRINDER, SAFETY WARNINGS
Safety guidelines for grinding, sanding with sandpaper, working
with wire brushes and cutting using the grinding wheel.
• This power tool can be used as a regular grinder, sander
for sanding with sandpaper, grinder for grinding with wire
brushes and for cutting with a cut-off wheel. Observe all safety
guidelines, instructions, descriptions and data provided with
the power tool. Failure to observe the following recommendations
may cause danger of electric shock, fire and/or serious injuries.
• This power tool cannot be used for polishing. When the power
tool is used for other works than it is designed for, it may contribute to
hazards and injuries.
• Do not use equipment, which is not designed and recommended
by the manufacturer specifically for this device. The fact that it
can be fastened to the power tool, does not guarantee safe operation.
• The permissible rotational speed of a working tool used cannot
be lower than the maximum rotational speed given on the
power tool. A working tool rotating faster than the permissible speed
may break and its parts may chip off.
• The outside diameter and thickness of a working tool must
correspond to dimensions of the power tool. A working tool of
incorrect dimensions may not provide sufficient control and covering
of the power tool.
• Working tools with threaded inserts must perfectly fit the
thread in the spindle. In case of working tools that are fastened
using a flange, the hole diameter of a working tool must fit the
flange diameter. Working tools, which cannot be precisely seated in
the power tool, rotate unevenly, vibrate heavily and may result in loss
of control over the power tool.
• Under no circumstances, should damaged working tools be
used. Before the power tool is used, accessories such as cut-off
wheels should be checked for chips and cracks, grinding wheels
should be checked for cracks, abrasion or heavy wear, while
wire brushes for loose or broken wires. When the power tool
or a working tool is dropped, it must be checked for damage
or another, undamaged tool should be used. If a working tool
is checked and fastened, the power tool should be switched on
for a minute at the highest speed, paying attention so that the
operator and bystanders are beyond the zone of the rotating
tool. Damaged working tools often break in this test period.
• Always wear personal protective equipment. Depending on a
type of work, a full face mask, eye protection or safety glasses
should be worn. A dust mask, ear protection, protective gloves
or a special apron protecting against small particles of abrasive
material and workpiece should be worn, if needed. Protect your
eyes against airborne foreign bodies occurring during operation. A
dust mask and protective mask for the respiratory system must filter
dust occurring during work. The influence of noise for a longer period
of time may lead to deterioration of the hearing.
• Always make sure bystanders are in a safe distance from the
power tool reach zone. All people staying in the vicinity of the
operating power tool must use personal protective equipment.
Chips of a workpiece or broken working tools may chip off and cause
injuries also beyond the direct reach zone.
• When works are performed, during which the power tool may
encounter hidden electric conductors or own power cord,
the power tool should be held by the isolated surfaces of the
11
