Bosch Professional GEX 125 AVE Manual Original página 17

Sanding Surfaces
Switch the power tool on, place the entire sanding surface
against the surface of the workpiece and apply moderate
pressure as you move the sander over the workpiece.
The material removal rate and sanding result are primarily
determined by the choice of sanding sheet, the preselected
orbital stroke rate level and the contact pressure.
Only immaculate sanding sheets achieve good sanding per-
formance and make the power tool last longer.
Be sure to apply consistent contact pressure in order to in-
crease the lifetime of the sanding sheets.
Excessively increasing the contact pressure will not lead to
increased sanding performance, rather it will cause more
severe wear of the power tool and of the sanding sheet.
Do not use a sanding sheet for other materials after it has
been used to work on metal.
Use only original Bosch sanding accessories.
Rough Sanding
Attach a coarse grit sanding sheet.
Apply only light pressure to the power tool so that it runs at a
higher orbital stroke rate and a higher material removal rate
is achieved.
Fine Sanding
Attach a fine grit sanding sheet.
You can reduce the sanding plate orbital stroke rate by
lightly varying the contact pressure or changing the orbital
stroke rate level; the random orbit motion will be retained.
Application
Intermediate lacquer sanding
Lacquer/varnish
Softwood
Hardwood
Veneer
Aluminium
Steel
Derusting steel
Stainless steel
Stone
Maintenance and Service
Maintenance and cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by a
customer service centre that is authorised to repair Bosch
power tools.
Bosch Power Tools
Move the power tool with moderate pressure flat on the
workpiece in a circular motion or alternately along and
across it. Do not tilt the power tool in order to avoid sanding
through the workpiece, e.g. veneers.
Switch the power tool off after completing operation.
Polishing
For polishing weathered lacquers and redressing scratches
(e.g. acrylic glass), the power tool can be fitted with an ap-
propriate polishing tool, e.g. lambswool bonnet, polishing
felt or polishing sponge (accessory).
Select a low orbital stroke rate (level 1–2) when polishing in
order to avoid heating up the surface excessively.
Apply the polish to an area slightly smaller than the area
which you intend to polish. Using the appropriate polishing
tool, work in the polish with either linear or circular move-
ments and with moderate pressure.
Do not allow the polish to dry out on the surface; this may
damage the surface. Do not expose the surface which you in-
tend to polish to direct sunlight.
Clean the polishing tool regularly to ensure good polishing
results. Wash the polishing tools with mild detergent and
warm water; do not use thinning agents.
Application Table
The information in the table below is the recommended val-
ues.
The best method for determining the best combination while
sanding or polishing is practical experimentation.
Grit
(coarse/fine sanding)
120/400
40/80
40/240
60/320
240/320
80/240
60/240
40/120
120/240
80/200
After-sales service and advice on using products
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
English | 17
Orbital stroke rate level
5/6
5/6
5/6
5/6
5/6
5
5
6
5
6
1 609 92A 49A | (17.05.2018)