Operation - Craftsman 315.DD2100 Manual Del Operador

WARnIng:
Do not allow familiarity with tools to
make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious injury.
WARnIng:
Always wear eye protection marked to
comply with ANSI Z87.1. Failure to do so could result
in objects being thrown into your eyes resulting in
possible serious injury.
WARnIng:
Do not use any attachments or
accessories not recommended by the manufacturer
of this tool. The use of attachments or accessories
not recommended can result in serious personal
injury.
APPLIcATIOnS
You may use this product for the purposes listed below:
 Drilling in all types of wood products (lumber, plywood,
paneling, composition board, and hard board)
 Drilling in ceramics, plastics, fiberglass, and laminates
 Drilling in metals
 Driving screws into wood and drywall with screwdriver
bits
This product will accept Craftsman
battery packs and Craftsman
battery packs.
For complete charging instructions, refer to the Operator's
Manual for your battery pack and charger models.
BATTERY PROTEcTIOn FEATuRES
Craftsman 19.2 V lithium-ion battery packs are designed
®
with features that protect the lithium-ion cells and
maximize battery life.
If the tool stops during use, release the trigger to reset
and resume operation. If the tool still does not work, the
battery needs to be recharged.
c3 EnERgY InDIcATOR WInDOW
See Figure 1, page i.
The C3 energy indicator window located on the side of
the handle, just above the base, will light when some
Craftsman 19.2 V lithium-ion battery packs are installed
®
and have charge (315.113710, 315.PP2000, 315.PP2010,
315. PP2020, 315. PP2030).
nOTE: Feature will not light with Craftsman
nickel-cadmium battery packs.

OPERATIOn

19.2 V lithium-ion
®
19.2 V nickel-cadmium
®
19.2 V
®
InSTALLIng/REmOVIng BATTERY PAck
See Figure 2, page i.
To install:
 Lock the switch trigger by placing the direction of
rotation selector in the center position.
 Place battery pack in the tool. Align raised rib on
battery pack with groove inside tool.
 Make sure the latches on each side of the battery pack
snap into place and battery pack is secured in tool
before beginning operation.
WARnIng:
your tool when you are assembling parts, making
adjustments, cleaning, or when not in use. Removing
battery pack will prevent accidental starting that
could cause serious personal injury.
To remove:
 Lock the switch trigger by placing the direction of
rotation selector in the center position.
 Locate latches on end of battery pack and depress to
release battery pack from the tool.
 Remove battery pack.
WARnIng:
operating condition. Therefore, the switch should
always be locked when not in use or carrying at your
side.
SWITcH TRIggER
See Figure 3, page i.
To turn the drill On, depress the switch trigger. To turn it
OFF, release the switch trigger.
VARIABLE SPEED
The variable speed switch trigger delivers higher speed
with increased trigger pressure and lower speed with
decreased trigger pressure.
nOTE: You might hear a whistling or ringing noise from
the switch during use. Do not be concerned; this is a nor-
mal part of the switch function.
DIREcTIOn OF ROTATIOn SELEcTOR
(FORWARD/REVERSE/cEnTER LOck)
See Figure 3, page i.
The direction of bit rotation is reversible and is controlled
by a selector located above the switch trigger. With the
drill held in normal operating position, the direction of
rotation selector should be positioned to the left of the
switch trigger for forward drilling. The drilling direction is
reversed when the selector is to the right of the switch
trigger.
7 - English
Always remove battery pack from
Battery products are always in