Check The Oil Level - Briggs & Stratton VANGUARD 25V000 Manual Del Operador

Fuel Level - Maximum
Do Not Overfill
Assembly
Throttle Control Conversion
The standard engine has a manual throttle control. To operate the manual throttle
control, install a remote throttle control, or convert to a fixed speed. Refer to the
instructions that follow.
NOTE: The engine speed must be correct as specified by the equipment
manufacturer's performance specifications. Contact a Briggs & Stratton Authorized
Service Dealer for assistance.
Manual Throttle Control
1.
Move the throttle control / TransportGuard
2. Remove the spring (S, Figure 3).
Remote Throttle Control with Braided Wire Cable
A remote throttle control with a braided wire cable can be installed in one of two
directions: Cylinder Head Direction or Front Direction.
Cylinder Head Direction
1. Use a 10 mm wrench and loosen the nut (P, Figure 4) ½ turn on the throttle control /
®
TransportGuard lever (A).
2. Hold the cable mounting nut (J, Figure 5) with a 10 mm wrench and loosen the
screw (K).
3. Install the cable wire (L, Figure 5) through the hole in the cable mounting nut (J),
and tighten the screw (K). Make sure that the cable wire (L) does not extend more
than ½" (12,7 mm) past the hole.
4. Loosen the screw (I, Figure 5). Attach the cable sleeve (N) under the cable clamp
(M), and tighten the screw (I).
5. Check the operation of the remote throttle control. Move the remote throttle control
from slow to fast 2-3 times. Make sure that remote throttle control and the cable
wire (L, Figure 5) moves freely. Adjust the nut (P, Figure 6) as necessary for the
specified position.
Front Direction
1. Use a 10 mm wrench and loosen the nut (P, Figure 3) ½ turn on the throttle
®
control / TransportGuard lever (A) to the OFF position.
2. Hold the cable mounting nut (J, Figure 7) with a 10 mm wrench and loosen the
screw.
3. Install the cable wire (L, Figure 7) through the hole in the cable mounting nut (J)
and tighten the screw (K). Make sure that the cable wire (L) does not extend more
than ½" (12,7 mm) past the hole.
4. Loosen the screw (I, Figure 7). Attach the cable sleeve (N) under the clamp (M) and
tighten the screw (I).
5. Check the operation of the remote throttle control. Move the remote throttle control
from slow to fast 2-3 times. Make sure that the remote throttle control and the cable
(L, 7) moves freely. Adjust the nut (P, Figure 3) as necessary for the specified
position.
Remote Throttle Control with Solid Wire Cable
A remote throttle control with a solid wire cable can be installed in one of four directions:
Cylinder Head Direction, Front Direction, Left Direction, or Right Direction.
Cylinder Head Direction
1.
Move the throttle control / TransportGuard
2. Remove the spring (S, Figure 8).
3. Use a 10 mm wrench and loosen the nut (P, Figure 3) ½ switch the throttle control /
®
TransportGuard lever (A).
4. Install the Z-fitting of the solid wire cable (Q, Figure 8) to one of the small holes in
the bellcrank (R).
5. Loosen the screw (I, Figure 8). Attach the cable sleeve (N) below the cable clamp
(M), and tighten the screw (I).
6. Examine the operation of the remote throttle control. Move the throttle control from
slow to fast 2-3 times. Make sure that remote throttle control and the cable wire (L,
Figure 8) moves freely. Adjust the nut (P, Figure 3) as required for the specified
position.
Front Direction
1.
Move the throttle control / TransportGuard
8
®
lever (A, Figure 3) to the OFF position.
®
lever (A, Figure 3) to the OFF position.
®
lever (A, Figure 3) to the OFF position.
2. Remove the spring (S, Figure 9).
3. Use a 10 mm wrench and loosen the nut (P, Figure 3) ½ turn on the throttle
®
control / TransportGuard lever to the OFF position.
4. Install the Z-fitting of the solid wire cable (Q, Figure 9) to one of the two small holes
in the bellcrank (R).
5. Loosen the screw (I, Figure 9). Attach the cable sleeve (N) under the clamp (M) and
tighten the screw (I).
6. Check the operation of the remote throttle control. Move the remote throttle control
from slow to fast 2-3 times. Make sure that the remote throttle control and the
cable (L, Figure 9) moves freely. Adjust the nut (P, Figure 3) as necessary for the
specified position.
Left Direction
1.
Move the throttle control / TransportGuard
2. Remove the spring (S, Figure 3).
3. Use a 10 mm wrench and loosen the nut (P, Figure 3) ½ turn on the throttle
®
control / TransportGuard lever (A, 10) to the OFF position.
4. Install the Z-fitting of the solid wire cable (L, Figure 10) to the small hole (S) in the
throttle control lever (A).
5. Loosen the screw (I, Figure 10). Attach the cable sleeve (N) under the clamp (M)
and tighten the screw (I).
6. Check the operation of the remote throttle control. Move the remote throttle control
from slow to fast 2-3 times. Make sure that the remote throttle control and the
cable (L, Figure 10) moves freely. Adjust the nut (P, Figure 3) as necessary for the
specified position.
Right Direction
To install a remote throttle control from the right direction, a cable mounting bracket
(U, Figure 11) is required. Refer to the Specifications and Service Parts section for
the part number. To purchase a cable mounting bracket, contact a Briggs & Stratton
Authorized Service Dealer.
1.
Move the throttle control / TransportGuard
2. Remove the spring (S, Figure 3).
3. Use a 10 mm wrench and loosen the nut (P, Figure 3) ½ turn on the throttle
®
control / TransportGuard lever (A, 11) to the OFF position.
4. Install the Z-fitting of the solid wire cable (L, Figure 11) to the small hole (S) in the
throttle control lever (A).
5. Remove the bolt (T, Figure 11). Install the cable mounting bracket (U) as shown.
Attach the cable mounting bracket (U) with the bolt (T). Tighten the bolt (T) to 30lb-
in (3,4 Nm). See Specifications and Service Parts section.
6. Loosen the screw (I, Figure 11). Attach the cable sleeve (N) under the clamp (M)
and tighten the screw (I).
7. Check the operation of the remote throttle control. Move the remote throttle control
from slow to fast 2-3 times. Make sure that the remote throttle control and the
cable (L, Figure 11) moves freely. Adjust the nut (P, Figure 3) as necessary for the
specified position.
Fixed Engine Speed (No Throttle Control Cable)
When converted to a Fixed Engine Speed, a throttle control cable is not installed and
there is no speed selection. FAST is the only engine speed.
1. Move the throttle control / TransportGuard® lever (A, Figure 12) to the OFF
position.
2. Remove the spring (S, Figure 12).
3.
Move the throttle control / TransportGuard
position.
4. Make sure the wire retainer screw (V, Figure 12) aligns with the hole in the bracket.
Tighten the screw (V) to 25 lb-in (2,8 Nm).
5. Remove the control link (H, Figure 12).
NOTE: At this time, the throttle control / TransportGuard
positions: STOP / OFF position and RUN position.
6.
Install the new ON / OFF TransportGuard
speed control label located on the trim panel (F).
Operation

Check the Oil Level

Before you check or add oil
• Make sure that the engine is level.
• Clean the oil area of debris.
• See the Specifications section for oil capacity.
®
lever (A, Figure 10) to the OFF position.
®
lever (A, Figure 11) to the OFF position.
®
lever (A, Figure 12) to the FAST
®
lever will only have two
®
label (O, Figure 13) over the existing