Manufacturer's Warranty - STEINEL XLED home curved S Manual Del Usuario

5� Mounting
• Check all components for damage.
• Do not use the product if it is damaged.
• Select an appropriate mounting location, taking the
reach and motion detection into consideration.
The most reliable way to detect movement is given by
mounting the light to point across the direction in which
people walk and by making sure no obstacles (e.g. trees,
walls etc.) interrupt the line of sensor vision.
Mounting procedure
• Switch OFF power supply. (Fig� 4�1)
• Unscrew locking screw. (Fig� 5�1)
• Detach enclosure from wall mount. (Fig� 5�2)
• Detach plug-in terminal from wall mount. (Fig� 5�3)
• Mark drill holes. (Fig� 5�4)
• Drill holes and fit wall plugs. (Fig� 5�5)
• Surface-mounted installation with spacers (Fig� 5�6)
• Concealed mounting (Fig� 5�7)
• Connect conductors. (Fig� 5�8) • Connect plug-in terminal. (Fig� 5�9)
• Fit enclosure onto wall mount. (Fig� 5�10)
• Screw in locking screw. (Fig� 5�11)
• Switch ON power supply. (Fig� 6�1)
• Make settings ➜ "6� Function"
6� Function
Factory settings:
– Twilight setting 1000 lux
– Time setting 2 seconds
Twilight setting (Fig� 6�2 E)
infinitely variable
Control dial set to = twilight operation, approx. 2 lux
Control dial set to = daylight operation, approx. 1000 lux
Note:
To adjust the detection zone in daylight, the control dial
must be set to = daylight operation.
Time setting (Fig� 6�2 F)
Control dial set to max = longest time, approx. 70 min
Control dial set to min = shortest time, approx. 2 seconds
Note:
When setting the detection zone, we recommend selecting
the shortest time.
7� Reach setting/adjustment
The detection zone can be optimised to suit requirements.
Adhesive shroud (Fig� 7�1)
The film shroud can be used for masking out any number
of lens segments to limit reach as required. Inadvertent trig-
gering is ruled out or the sensor can be targeted to watch
over danger spots. (Fig� 7�2/7�3/7�4)
Floodlight adjustment range (Fig� 7�5)
8� Maintenance and care
The product requires no maintenance.
The floodlight can be cleaned with a damp cloth (without
detergents) if dirty.
Important note: the control gear cannot be replaced.
9� Disposal
Electrical and electronic equipment, accessories and pack-
aging must be recycled in an environmentally compatible
manner.
EU countries only:
Under the current European Directive on Waste Electri-
cal and Electronic Equipment and its implementation in
national law, electrical and electronic equipment no longer
suitable for use must be collected separately and recycled
in an environmentally compatible manner.
10� Manufacturer's warranty
This Steinel product has been manufactured with utmost
care, tested for proper operation and safety and then sub-
jected to random sample inspection. Steinel guarantees
that it is in perfect condition and proper working order. The
warranty period is 36 months and starts on the date of sale
to the consumer. We will remedy defects caused by ma-
terial flaws or manufacturing faults. The warranty will be
met by repair or replacement of defective parts at our own
discretion. The warranty shall not cover damage to wear
parts, damage or defects caused by improper treatment or
maintenance. Further consequential damage to other ob-
jects shall be excluded.
Claims under the warranty will only be accepted if the unit
is sent fully assembled and well-packed with a brief de-
scription of the fault, a receipt or
invoice ( date of purchase and dealer's stamp ) to the ap-
propriate Service Centre.
Repair service:
If defects occur outside the warranty period or are not cov-
ered by the warranty, ask your nearest service station for
G B
the possibility of repair.
1 3
Y E A R
MANUFACTURER'S
WARRANTY
- 12 -
Do not dispose of electrical and electronic
equipment as domestic waste.
5
Y E A R
MANUFACTURER'S
WARRANTY
Y E A R
MANUFACTURER'S
WARRANTY