V2 CU1 Manual Del Usuario página 11

To delete all the codes by means of a transmitter non-stored,
proceed as follows:
1. Position the retractable at the mid-height.
2. Switch off power supply of the system.
3. Set on ON the switch 3 of a transmitter.
4. Press and keep pressed the button PROG.
5. Supply power only to the control unit on which to make the
deletion: after about 1 second the motor moves in both the
ways showing the correct deletion.
6. Release the button PROG and set on OFF the switch 3.
Switch 7: storing of the level of intervention
of the wind sensor
To set the level of intervention of the wind sensor it is necessary
to use a remote control previously stored and proceed as follows:
WARNING: to make the awning close, the wind sensor has
to detect a value higher then the set threshold value for at least 5
seconds. The automation is blocked for 8 minutes when the
awning is closed because of strong wind.
1. DUO6 / DUO4 only: press several times the button SELC of the
transmitter until shown by leds the channel stored.
2. Position the roll-up shutter at the mid-height
3. Set on ON the switch 7 of the transmitter.
4. Press and keep pressed (for 5 about seconds) the button PROG
of the transmitter until the motor moves jerkily in both the
ways showing that it enters the storing.
5. The number of jerks made by the motor corresponds to the
level currently set:
1 jerk = level 1 = 10 Km/h (default)
2 jerks = level 2 = 15 Km/h
3 jerks = level 3 = 20 Km/h
4 jerks = level 4 = 30 Km/h
5 jerks = level 5 = 40 Km/h
6. To increase the level press button UP, to decrease it press
button DOWN.
7. As soon as the control unit receives the control, it shows the
new level moving the motor with the corresponding number
of jerks.
8. To exit the programming press STOP: the motor displays again
the set level and exits.
Switch 8: programming of the level of
intervention of the sun sensor
To set the level of intervention of the sun sensor it is necessary to
use a remote control previously stored and proceed as follows:
WARNING: to make the awning open the sun sensor has to
detect a value higher then the set threshold value for at least 8
minutes. To make it close, the sensor has to detect a value lower
then the set threshold value for at least 8 minutes.
Interruptions of light (due to clouds) shorter than a minute are
not detected, while the 8-minute timer is set at zero when longer
than one minute.
1. DUO6 / DUO4 only: press several times the button SELC of the
transmitter until shown by leds the channel stored.
2. Position the roll-up shutter at the mid-height
3. Set on ON the switch 8 of the transmitter.
4. Press and keep pressed (for 5 about seconds) the button PROG
of the transmitter until the motor moves jerkily in both the
ways showing that it enters the storing.
All manuals and user guides at all-guides.com
5. The number of jerks made by the motor corresponds to the
6. To increase the level press button UP, to decrease it press
7. As soon as the control unit receives the control, it shows the
8. To exit the programming press STOP: the motor displays again
Disabling of the sun sensor
To disabling the sun sensor proceed as follows:
1. DUO6 / DUO4 only: press several times the button SELC of the
2. Position the roll-up shutter at the mid-height
3. Press the key STOP and immediately after the key DOWN
To enable again the sun sensor it is enough to repeat the
procedure above using the key UP instead of the key DOWN.
Switch 10: Programming of the level of
temperature
The temperature can be set on 5 levels, under which the sun
sensor must not open the awning, even if the light intensity has
exceeded the level set by switch 8
This function is particularly useful in Countries with wintry
weather, where sunny but very cold days are frequent. In this
case, it is not necessary to open the awnings, to let the sun warm
the inner rooms.
To set the level of temperature it is necessary to use a remote
control previously stored and proceed as follows:
1. DUO6 / DUO4 only: press several times the button SELC of the
2. Position the roll-up shutter at the mid-height
3. Set on ON the switch 10 of the transmitter.
4. Press and keep pressed (for 5 about seconds) the button PROG
5. The number of jerks made by the motor corresponds to the
6. To increase the level press button UP, to decrease it press
7. As soon as the control unit receives the control, it shows the
8. To exit the programming press STOP: the motor displays again
9
level currently set:
1 jerk = level 1 = 2 Klux
2 jerks = level 2 = 5 Klux
3 jerks = level 3 = 10 Klux (default)
4 jerks = level 4 = 20 Klux
5 jerks = level 5 = 40 Klux
button DOWN.
new level moving the motor with the corresponding number
of jerks.
the set level and exits.
transmitter until shown by leds the channel stored.
(keeping pressed the key STOP) until the motor moves for
about one second in both the ways, indicating that the
procedure has been finished.
transmitter until shown by leds the channel stored.
of the transmitter until the motor moves jerkily in both the
ways showing that it enters the storing.
level currently set:
1 jerk = level 1 = sensor disabled (default)
2 jerks = level 2 = 0°C
3 jerks = level 3 = 5°C
4 jerks = level 4 = 10°C
5 jerks = level 5 = 15°C
button DOWN.
new level moving the motor with the corresponding number
of jerks.
the set level and exits.