V2 CU1 Manual Del Usuario página 10

PROGRAMMING OF THE FUNCIONTS BY
MEANS OF TRANSMITTERS OF THE RANGE
DUO
Using a transmitter of the range DUO it is possible changing the
functions of the control unit controlling the tubular motor.
DUO is equipped with a 10 switches dip-switch thanks to which
it is possible to change the desired functions: set on ON the
switch corresponding to the function required and follow
carefully the dedicated procedure.
WARNING: all the other switches have to be set on OFF
DIP FUNCTION
1 Storage of the transmitters
3 Deletion of all the stored transmitters
Storing of the level of intervention of the wind
7
sensor
Programming of the level of intervention of the sun
8
sensor
10 Programming of the level of temperature
2 - 4 - 5
NOT USED
6 - 9
All manuals and user guides at all-guides.com
Switch 1: Storage of the transmitters
To store a transmitter TX1 on a blank control unit proceed as
follows:
WARNING: the first transmitter stored fixes the direction of
motion of the motor.
1. Power only the control unit to be programmed
2. Set on ON the switch 1 of the transmitter.
3. DUO6 / DUO4 only: press several times the key SELC of the
4. Press and keep pressed (for about 5 seconds) the key PROG of
5. Release the key PROG: the motor stops.
6. Press the keys UP or DOWN depending on the way of motion
7. Set the switch 1 to OFF.
Try to operate the roll-up shutter and check that it works with the
logic above described. If the logic is reversed, it is necessary to
delete all the codes stored (read Switch 3) and start again the
above procedure.
To add another transmitter TX2 to the control unit it is necessary
to use a remote control previously stored (TX1) and proceed as
follows:
1. DUO6 / DUO4 only: press several times the key SELC of the
2. DUO6 / DUO4 only: press several times the key SELC of the
3. Take the roll-up shutter to half its way with TX1.
4. Set to ON the switch 1 of the transmitter TX1.
5. Press and keep pressed for about 5 seconds the key PROG of
6. Release the key PROG, the motor stops.
7. Press the key UP or DOWN of the TX2: the transmitter is
Switch 3: deletion of all the stored
transmitters
To delete all the transmitters stored on the control unit it is
necessary using a remote control previously stored and proceed
as follows:
1. Power only the control unit to be programmed
2. DUO6 / DUO4 only: press several times the button SELC on
3. Position the roll-up shutter at the mid-height.
4. Set on ON the switch 3 of the transmitter.
5. Press and keep pressed the button PROG of the transmitter
6. Release the button PROG and set on OFF the switch 3 of the
8
transmitter TX1 until displayed the selected channel (by the
leds or on the display).
the transmitter TX1 until the motor starts to move in one way.
of the roll-up shutter before stopping:
- if the roll-up shutter was going up, press the key UP;
direction acquired: the key UP moves the roll-up shutter
UPWARDS, the key DOWN moves the roll-up shutter
DOWNWARDS.
- if the roll-up shutter was going down, press the key DOWN;
direction acquired: the key DOWN moves the roll-up shutter
DOWNWARDS, the key UP moves the roll-up shutter
UPWARDS.
transmitter TX1 until displayed the channel stored (by the leds)
new transmitter TX2 until display the channel to be stored (by
the leds)
the TX1 until the motor starts to move.
stored with the same logic of the TX1.
the transmitter until displayed the channel stored (by the leds)
until the motor moves in both the ways for 1 second, showing
the end of deletion.
transmitter.