Assembly Of Pruner Device; Extension Of The Pruner Device; Removing The Pruner Device; Controls - Stiga MP 20 Li A Manual De Instrucciones

Ocultar thumbs Ver también para MP 20 Li A:
Tabla de contenido
If the tip of the bar is equipped with a nose
sprocket, make sure the drive links are
correctly inserted in the sprocket rims (Fig. 6).
4. Check that chain tension adjuster pin
(Fig. 5.C) is inserted correctly in the
hole on the bar; if it isn't, turn the chain
tension adjuster screw (Fig. 5.D), until
the pin is completely inserted.
5. Replace the guard without
fully tightening the knob.
6. Turn the chain tension adjuster screw (Fig.
5.D) to achieve the desired tension (Fig. 7).
7. Raise the bar and tighten the
knob (1) securely (Fig. 8.A).
4.2.1 Checking the chain tension
Check the chain tension.
The tension is correct when the drive links
do not slip out of the chain guides if you hold
the chain in the middle of the bar (Fig. 7)

4.3 ASSEMBLY OF PRUNER DEVICE

Before assembling, make sure the
battery is not fitted in its housing.
1. Insert the pruner device (Fig. 9.A) in the
control rod (Fig. 9.B)
(Fig. 9.C)
click into the hole
rod. Insertion is completed when the stop
pins protrude completely from the hole.
2. Close the clamping lever (Fig. 9.A).
Periodically check that the
joints are well tightened.

4.4 EXTENSION OF THE PRUNER DEVICE

1. Open the clamping lever (Fig. 10.A).
2. Pull or push the rod (Fig. 10.B) until
it reaches the desired length.
3. Close the clamping lever (Fig. 10.A).
Periodically check that the
joints are well tightened.

4.5 REMOVING THE PRUNER DEVICE

Wait until the motor is sufficiently
cold before removing the pruner device.
To remove the pruner device (Fig. 9.A):
1. Place the control rod (Fig. 9.B) on the ground.
2. Open the clamping lever (Fig. 9.E).
Direction in which
the chain runs
until the stop pins
(Fig.9.D)
in the
3. Push on the stop pin (Fig. 9.C) and
remove it from the hole (Fig. 9.D).
4. Disassemble the pruner device.

5. CONTROLS

5.1 THROTTLE TRIGGER LEVER

The throttle trigger lever (Fig.11.A) allows
the activation of the cutting means.
The activation of the throttle trigger lever
(Fig. 11.A) is only possible if the throttle
lock button is pressed (Fig. 11.B).

5.2 THROTTLE LOCK BUTTON

The throttle lock button (Fig. 11.B) allows the
throttle trigger lever to be used (Fig. 11.A).

6. USING THE MACHINE

The safety regulations to follow
are described in chap. 2. Strictly
comply with these instructions to
avoid serious risks or dangers.

6.1 PRELIMINARY PROCEDURES

Place the machine in a stable
horizontal position on the ground.
6.1.1 Checking and recharging
the battery (Fig. 12)
Before each use check the battery
charge status according to the
instructions in the battery booklet.
6.1.2 Using the harness
Frequently check the efficiency of the
quick release in order to free the machine
quickly from the belts in the event of danger.
The harness must be put on before
connecting the machine to the special
coupling and the belt must be adjusted
to suit the operator's height and build.
1. The belt (Fig. 13.A) must go from
the left shoulder to the right hip.
2. Hook the carabiner (Fig. 13.B) to the special
coupling located on the control rod.
3. If necessary, release the clip
buckle (Fig. 13.C) to remove the
machine from the harness.
EN - 8
Tabla de contenido
loading

Este manual también es adecuado para:

Mp 20 li s

Tabla de contenido