General Safety Information; Work Area Safety; Electrical Safety; Personal Safety - RIDGID 1224 Manual Del Operador

1224 Pipe and Bolt Threading Machine

General Safety Information

WARNING
Read and understand all instructions. Failure to fol-
low all instructions listed below may result in
electric shock, fire, and/or serious personal injury.
SAVE THESE INSTRUCTIONS!

Work Area Safety

1. Keep work area clean and well lit. Cluttered
benches and dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep bystanders, children, and visitors away
while operating a power tool. Distractions can
cause you to lose control.
4. Do not let visitors contact the tool or extension
cord. Such preventative measures reduce the risk of
injury.

Electrical Safety

1. Grounded tools must be plugged into an outlet,
properly installed and grounded in accordance
with all codes and ordinances. Never remove the
grounding prong or modify the plug in any way.
Do not use any adapter plugs. Check with a qual-
ified electrician if you are in doubt as to whether
the outlet is properly grounded. If the tools should
electrically malfunction or break down, grounding
provides a low resistance path to carry electricity
away from the user.
Grounding pin
2. Avoid body contact with grounded surfaces such
as pipes, radiators, ranges and refrigerators. There
is an increased risk of electrical shock if your body is
grounded.
3. Don't expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electrical shock.
2
Cover of
grounded
outlet box
Grounding pin
Ridge Tool Company • Elyria, Ohio • U.S.A.
4. Do not abuse cord. Never use the cord to carry the
tools or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges or moving parts.
Replace damaged cords immediately. Damaged
cords increase the risk of electrical shock.
5. When operating a power tool outside, use an out-
door extension cord marked "W-A" or "W". These
cords are rated for outdoor use and reduce the risk of
electrical shock.
6. Connect the tool to an AC power supply that
matches the name plate specifications. Incorrect
voltage supply can cause electrical shock or burns.
7. Use only three-wire extension cords which have
three-prong grounding plugs and three-pole re-
ceptacles which accept the machine plug. Use of
other extension cords will not ground the tool and in-
crease the risk of electrical shock.
8. Use proper extension cords. (See chart.) Insufficient
conductor size will cause excessive voltage drop,
loss of power and overheating.
Minimum Wire Gauge for Cord Set
Nameplate
Total Length (in feet)
Amps
0 – 25
0 – 6 18 AWG
6 – 10 18 AWG
10 – 12 16 AWG
12 – 16 14 AWG

Personal Safety

1. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medications. A moment of inat-
tention while operating power tools may result in
serious personal injury.
2. Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, cloth-
ing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving
parts.
3. Avoid accidental starting. Be sure switch is OFF
before plugging in. Carrying tools with your finger on
the switch or plugging tools in that have the switch ON
invites accidents.
4. Remove adjusting keys or switches before turning
the tool ON. A wrench or a key that is left attached to
a rotating part of the tool may result in personal injury.
26 – 50 51 – 100
16 AWG 16 AWG
16 AWG 14 AWG
16 AWG 14 AWG
12 AWG
NOT RECOMMENDED