EN
PRODUCT DESCRIPTION
1. Long slot nozzle
2. Long slot nozzle attachment
3. Slot nozzle
4. Long slot nozzle attachment - brush
5. Nozzle for wet vacuuming
6. Turbo nozzle
7. Charging base
8. Accessory stand
9. Charger connector
18
17
16
15
14
13
12
11
46
10. Charger
11. On/Off switch
12. Charging indicator
13. Dust container release button
14. Appliance body
15. LED lighting
16. HEPA filter
17. Filter holder
18. Dust container
1
3
2
5
4
6
7
8
9
10
VP4360 / VP4370 / VP4380
OPERATING INSTRUCTIONS
ASSEMBLING THE VACUUM CLEANER
Warning
Always switch off the appliance and disconnect the charger from wall socket before assembling or removing accessories!
ACCESSORIES
The following accessories are included in the package for each type of appliance:
- VP4360: 1, 4, 5, 7, 8, 10 (see product description)
- VP4370: 1, 5, 6, 7, 8, 10 (see product description)
- VP4380: 1, 2, 3, 4, 6, 7, 8, 10 (see product description)
Note: For VP4360 and VP4370 vacuum cleaners, only one part of the accessory stand is included, which is sufficient for
the accessories included in the product package.
CHARGING THE BATTERY
- Make sure the vacuum cleaner is turned off before charging. The charger (10) can be connected directly to the
vacuum cleaner or paired with the charging base (7). Connect the vacuum cleaner to the charger connector (9).
- When charging, the charging indicator (12) flashes red. When fully charged, the indicator light is green. When
charging is complete, the appliance automatically switches to recharging. However, do not leave the vacuum
cleaner permanently connected to the charger to avoid possible damage to the battery or its capacity.
- If the charging indicator (12) starts flashing green during vacuuming, the vacuum cleaner is discharged and will
turn off within about 1 minute.
- If the vacuum cleaner is completely discharged, the charging indicator (12) starts flashing alternately green and red
!
when the appliance is switched on. The vacuum cleaner must be charged.
IF YOU WANT TO KEEP THE BATTERY LIFE AS LONG AS POSSIBLE, CHARGE IT AFTER IT IS FULLY DISCHARGED.
INSTALLING THE CHARGING BASE
The charging base can be used as freestanding (in this case, place the base on a flat and stable surface) or attached to
the wall (attach the charging base to the wall with dowels and screws).
Note: In both cases, the accessory stand (8) can be attached to the charging base (7).
USING THE VACUUM CLEANER
Note: VP4360 and VP4370 vacuum cleaners can be used for both dry and wet vacuuming. Make sure that both the filter
holder and the HEPA filter are fitted correctly before use.
1. Remove the vacuum cleaner from the charging base.
2. Slide the switch (11) to position 1 to switch the vacuum cleaner on at a lower power level (the charging indicator
(12) light is yellow).
3. Slide the switch (11) to position 2 to switch the vacuum cleaner on at a higher power level (the charging indicator
(12) light is green).
4. For wet vacuuming (VP4360 and VP4370 only), use a wet vacuum nozzle that has a wiper function and the vacuum
cleaner sucks liquid when moving backwards. Move the vacuum cleaner very carefully to prevent liquid from
entering the vacuum cleaner motor. Do not shake or turn over the vacuum cleaner. The filter holder and the HEPA
filter only prevent the liquid from being sucked into the vacuum cleaner motor, but do not act as a protection
against liquid ingress into the vacuum cleaner motor. The maximum amount of liquid sucked is approximately
150 ml. At larger amounts, the liquid will flow through the nozzle back out of the dust container.
Note: For wet vacuuming, vacuum only at a lower power level (switch in position 1) and do not overfill the dust
container more than the marked "MAX" line.
VP4380 vacuum cleaner is not designed for vacuuming liquids!
VP4360 / VP4370 / VP4380
EN
!
47