Protecting The Environment; Technical Data - Stanley SL1M09 Manual De Instrucciones

2. The battery may be completely discharged. Charge the unit following the directions in this manual.
3. If the spotlight does not operate after recharging as directed, contact the manufacturer.
MaIntenance
Your spotlight has been designed to operate over a long period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and regular cleaning.
Except for the H3, 55 watt bulb, there are no user-replaceable parts. Periodically inspect the condition of chargers,
connectors and wires. Contact manufacturer to replace any components that have become worn or broken.
WARning: Before performing any maintenance or cleaning of the spotlight, unplug the unit from the power supply.
• From time to time wipe the appliance with a damp cloth. Do not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water.
spotlight bulb replacement
To replace the bulb, you will need a small cross-head screwdriver and a 6 volt, H3 55 watt replacement bulb. During
installation, avoid touching the glass part of the bulb. Bulb life may be shortened by installing a bulb with dirt or
fingerprints on it. The bulb can be wiped clean with a cloth moistened with alcohol.
RubbER Ring guARD
glAss
use a screwdriver to gently
lEns
pry the rubber bezel off.
REtAining
Ring
HAlOgEn bulb AssEMblY
HAiRPin
REtAining
WiRE
ligHt REFlEctOR
1. Disconnect the unit from any charging adapters.
2. Push the rubber bezel forward toward the front of the spotlight to reveal two small cross-head screws in the
retaining ring.
3. Using the screwdriver, remove (counterclockwise) the two screws. set them aside.
4. Lift off the retaining ring, glass lens and rubber "O" ring and set them aside.
5. Carefully remove the reflector and bulb assembly.
6. Disconnect the bulb wire from the red power wire.
7. Unsnap the hairpin retaining wires from the reflector's flange.
8. Using the screwdriver, loosen the retaining screw to remove the bulb from the reflector (no need to completely
remove this screw).
9. Lift out the bulb and detach wire.
10. Insert the replacement bulb into the reflector's flange.
11. Put back and secure the hairpin retaining wires.
12. Connect the bulb power wire to the red power wire.
13. Tighten the retaining screw on the flange.
EnglisH
SL1M09EU_Manual_040612.indd 6-7
ligHt cROss-HEAD scREW
REFlEctOR
On/OFF
cROss-HEAD
scREW tRiggER
RubbER
"O" Ring
HAlOgEn bulb
AssEMblY
Only replace the bulb in an integrated
assembly of lamp holder, wire and tab.
REtAining
scREW
6
14. Place the reflector in position in the body of the spotlight.
15. Replace the rubber "O" ring in the groove around the perimeter of the reflector.
16. Replace glass and retaining ring so the screw holes are aligned.
17. secure retaining ring with two screws.
18. Replace rubber bezel.
19. Operate switch to ensure proper operation of spotlight.
WARning: To reduce the risk of electric shock, replace bulb with 6 volt, H3 55 watt only.
replacing the fuse in the 12V dc charger
• Remove the gold cap by turning it counter clockwise.
• Remove the rubber washer, centre pin and the spring.
• Remove the fuse.
• Fit a new fuse of the same type and size (2 amp/250 volt).
• Install the centre pin, spring and rubber washer.
• Install the gold cap by turning clockwise onto the plug.

protectIng the enVIronMent

correct disposal of this product
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was purchased.
They can take this product for environmentally safe recycling.
separate collection of used products and packaging allows materials to be recycled and
used again. Re-use of recycled materials helps prevent environmental pollution
and reduces the demand for raw materials.
Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites
or by the retailer when you purchase a new product.

technIcal data

spotlight
Bulb: 6 volt, H3, 55 watt
Battery: Maintenance-free, sealed lead acid, 6 volt, 3 Ah
Mains charger Input 220-240 Vac
(EU and gB models) Output 12Vdc (500mA)
12 volt Dc charger
Voltage: 12 volts DC
DC Plug Fuse: 2A/250V
lIMIted Warranty
Manufacturer issues this limited warranty to the original purchaser of this product. This limited warranty is not
transferable and is only valid for non-commercial use. Manufacturer warrants this unit for 2 years from the date of
purchase against defective workmanship or material. It is the obligation of the purchaser to forward the unit together
with proof of purchase to the manufacturer or its representative with transportation cost prepaid. This warranty is void if
the unit is abused, handled carelessly or repaired by anyone other than manufacturer or its authorized representative.
Manufacturer makes no warranty other than this limited warranty and expressly excludes any implied warranty including
any warranty for consequential damages. This is the only expressed limited warranty and manufacturer neither
assumes nor authorizes anyone to assume or make any other obligation towards the product other than this limited
warranty.
Baccus Worldwide LLC
Weena 290
3012 NJ Rotterdam or
Postbus 819, 3000 AV Rotterdam
7 EnglisHn
4/6/2012 12:12:52 PM