Automatic Stop System; Care And Maintenance; Help With Faults - Lavor Nhp galaxy 140 Manual De Instrucciones

EN
the mains lead of this appliance may not correspond
with the coloured markings identifying the termi-
nals in your plug, proceed as follows:
The wires that is coloured Brown must be connected
to the terminal which is marked with the letter L or
coloured Red. The wire that is coloured Blue must be
connected to the terminal wich is marked with the
letter N or coloured Black.
it is a moulded on plug), the flexible cord insula-
tion should be stripped back as appropriate and a
suitable 3 pin plug fitted.
•
WARNING: Dispose of a plug that has been cut
from the power supply cord, as such a plug is haz-
ardous if inserted in a live 13A socket outlet else-
where in the house.
- Should the fuse need to be replaced an ASTA
marked fuse, approved to BS1362, of the same
rating must be used.
- Always replace the fuse cover after fitting a fuse.
The plug must NOT be used if the cover is omitted
or lost until a replacement is obtained.
- Make certain that only the correct fuse cover is
used and fitted.
- For plugs with detachable fuse cover the replace-
ment must be the same as the colour insert in the
base of the plug, or as directed by the embossed
wording on the base of the plug.
- If the detachable fuse cover is lost a replacement
may be purchased from a Service Centre.
Information for supply may also be obtained
from the plug manufacturer.
<20 m
20 m - 50 m ø 2,5 mm
fare rev04 man gener idro hobby 27l.indd 18
Safety points for
rewireable
moulded plug:
The mains lead
of this appliance
may be already fit-
ted with a BS1363
13A plug.
-
If your socket out-
let is not suitable
for the plug, then
the plug must be
removed (cut off if
<16 A <25 A
ø 1,5 mm 2 ø 2,5 mm
14 AWG 12 AWG
ø 4,0 mm
2
12 AWG 10 AWG
PLEASE NOTE: This water cleaner is equipped with
the A.S.S. (Automatic Stop System), which stops the
machine during the bypass phase. To start the water
cleaner, it is therefore necessary to set the switch on
position (I)"ON"; after that press the pistol trigger:
the Automatic Stop System will start the machine
or
and will stop it automatically when the trigger is
released. It is advisable to put on the safety of the
pistol trigger whenever the machine is stopped, in
order to avoid unintentional starting.
• Any automatic start of the machine without
pressing the gun trigger is attributable to air
bubbles in the water or other similar phenom-
ena which do not imply the existence of any de-
fects in the machine.
• Do not leave the appliance unattended during
the standby for more than 5 minutes. Contrarily,
for the safety of the appliance it is necessary to
re-turn the switch into the (0) OFF position.
• Please check that the coupling of the high pres-
sure hose with the appliance and the gun sup-
plied as standard equipments made correctly,
that is to say without any water leak.
>

CARE AND MAINTENANCE

The unit is maintenance-free.
•
Disconnect the appliance from the power sup-
ply network before making any maintenance
and cleaning operation.
>

HELP WITH FAULTS

Appliance does not work
• Check whether the voltage shown on the rat-
ing plate corresponds to that of the power
source.
• Check the connector cable for damage.
Appliance does not reach operational pressure
• Vent the appliance: allow the pump to operate
without the high-pressure hose until water ap-
2
pears at the high-pressure outlet without any
more bubbles. Then reattach the high-pres-
2
sure hose.
18
(if fitted)
6-04-2010 8:28:51