Changing The Oil; Servicing The Air Filter - Briggs & Stratton 2691691-00 Manual Del Operario

component. If there is any doubt about the cause of the
problem, see your dealer.
To charge the battery, follow the instructions provided by the
battery charger manufacturer as well as all warnings included
in the Operator Safety section of this manual. Charge the
battery until fully charged. Do not charge at a rate higher than
10 amps.
Seat And Ground Speed Lever
Adjustments
The seat and ground speed levers should be adjusted so
that the ground speed levers can be moved through their full
range of motion without contacting the operator's legs.
Seat Adjustment
1. Raise the seat.
2. Loosen the adjustment hardware (A or B, Figure 19,
depending on seat type) under the seat base.
3. Slide the seat forward or backward to the desired
position.
4. Tighten the hardware to 80 lb-in (9 Nm).
Ground Speed Lever Adjustment
1. Loosen the ground speed lever mounting hardware (A,
Figure 20) to adjust the levers forward and backward.
2. Remove the hardware to raise or lower the levers.
3. Always be sure to adjust both levers so that they are
aligned (B, Figure 20).
4. After adjustment is complete, tighten the hardware to 13
lb-ft (18 Nm).
Speed Balancing (Tracking) Adjustment
If the rider drifts to the right or left when the ground speed
levers are in the maximum forward position, the top speed of
each of these levers can be balanced. Only adjust the speed
of the wheel that is traveling faster.
1. Tighten the knob (A, Figure 21) of the faster wheel by 1/2-
turn (clockwise) increments until the rider travels (tracks)
straight.
WARNING
Unsafe Operation Hazard
DO NOT adjust the rider for a faster overall speed
forward or reverse than it was designed.
Mower Removal And Installation
Refer to the Mower Deck Manual for instructions on removing
and installing the mower deck.
Mower Deck Leveling
Refer to the Mower Deck Manual for instructions on leveling
the mower deck.

Changing The Oil

Used oil is a hazardous waste product and must be disposed
of properly. Do not discard with household waste. Check
with your local authorities, service center, or dealer for safe
disposal/recycling facilities.
Draining The Oil
1. With engine off but still warm, disconnect the spark plug
wire (A, Figure 22) and keep it away from the spark plug.
2. Remove the dipstick (B, Figure 22).
Standard Oil Drain Plug
1. Remove the oil drain plug (C, Figure 22). Drain the oil into
an approved container.
2. After the oil has drained, install and tighten the oil drain
plug.
Optional Quick Oil Drain
1. Disconnect the oil drain hose (H, Figure 23) from the side
of the engine.
2. Turn and remove the oil drain cap (I, Figure 23). Carefully
lower the quick oil drain (H) into an approved container
(J).
3. After the oil has drained, install the oil drain cap. Attach
the oil drain hose to the side of the engine.
Changing The Oil Filter
For replacement intervals, see Maintenance Schedule.
1. Drain the oil from the engine. See Draining The Oil .
2. Remove the oil filter (K, Figure 24) and dispose of
properly.
3. Before installing the new oil filter, lightly lubricate the oil
filter gasket with fresh, clean oil.
4. Install the oil filter by hand until the gasket contacts the oil
filter adapter, then tighten the oil filter 1/2 to 3/4 turns.
5. Add oil. See Operation - Check Oil Level .
6. Start and run the engine. As the engine warms up, check
for oil leaks.
7. Stop the engine and check the oil level.

Servicing The Air Filter

WARNING
Fire and Explosion Hazard
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
• Never start or run the engine with the air cleaner
assembly or air filter removed.
NOTICE
Do not use pressurized air or solvents to clean the filter.
Pressurized air can damage the filter and solvents will
dissolve the filter.
15