Maintenance / Service - Skil 0700 Manual Original

MAINTENANCE / SERVICE

• This tool is not intended for professional use
• Always keep tool and cord clean
! disconnect the plug before cleaning
- regularly clean ventilation slots Q 2 with a soft cloth
- regularly remove dirt from cutting guard A 2 with a
soft brush
• Storage *
- store the tool indoors in a dry and locked-up place,
out of reach of children
- securely mount storage rail R on the wall with 4 screws
(not supplied) and horizontally leveled
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
TROUBLESHOOTING
• The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! switch off the tool and disconnect the plug before
investigating the problem
★ Tool does not operate
- power supply socket faulty -> use another socket
- extension cord damaged -> replace extension cord
- brush incorrectly mounted -> mount brush again
★ Tool operates intermittently
- internal wiring defective -> contact dealer/service
station
- on/off switch defective -> contact dealer/service
station
★ Weed is not removed completely
- brush damaged/worn -> replace brush
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 5 will remind you of this when the need for
disposing occurs
NOISE/VIBRATION
• Measured in accordance with EN 60335 the sound
pressure level of this tool is 76.2 dB(A) (standard
deviation: 3 dB) and the sound power level 99 dB(A), and
the vibration 6.37 m/s² (triax vector sum; uncertainty K =
1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60335; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Brosse à mauvaises herbes
INTRODUCTION
• Cet outil a été conçu pour enlever les mauvaises herbes
des terrasses et entre les carreaux
• Cet outil n'est conçu pour un usage professionnel
• Vérifiez que le conditionnement contient toutes les
pièces présentées dans le schéma 2
• Lorsque des pièces manquent ou sont endommagées,
veuillez contacter votre distributeur
• Lisez attentivement ce manuel d'instruction avant
d'utiliser l'outil et conservez-le pour pouvoir vous y
référer ultérieurement 3
• Prêtez attention aux consignes de sécurité et aux
avertissements; ne pas suivre ces instructions peut
entraîner des graves blessures
CARACTERISTIQUES TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A Protection de coupe
B Roue
C Vis de fixation
D Bouton de blocage de l'arbre
E Chapeau
F Clé
G Brosse
H Indicateur de brosse
J Douille de verrouillage
K Tube télescopique
L Poignée
M Dispositif d'immobilisation du cordon d'alimentation
N Interrupteur de sécurité
P Gâchette
Q Fentes de ventilation
R Rail de rangement (vis non fournies)
12
0700