Placement; Cables; The Rr-Dd91 Remote Control; Remote Control Batteries - Rotel RDD-1580 Manual De Instrucciones

8
Save the shipping carton and all enclosed packing material for future use.
Shipping or moving the RDD-1580 in anything other than the original packing
material may result in severe damage that is not covered by the warranty.
If included in the box please fill out and send in the owner`s registration
card. Also be sure to keep the original sales receipt. It is your best record
of the date of purchase, which you will need in the event warranty service
is required.

Placement

Like all audio components that handle low-level signals, the RDD-1580 can
be affected by its environment. Avoid placing the RDD-1580 on top of other
components. Also avoid routing audio signal cables near power cords. This
will minimize the chance it will pick up hum or interference.
We recommend installing the unit in furniture designed to house audio
components. Such furniture is designed to reduce or suppress vibration which
can adversely affect sound quality. Ask your authorized Rotel dealer for advice
about component furniture and proper installation of audio components.
The RDD-1580 is supplied with an RR-DD91 remote control and must be
placed where the infrared signal from the remote can reach the front panel

Remote Sensor.

Cables

Be sure to keep the power cords, digital signal cables and regular audio
signal cables in your installation away from each other. This will minimize
the chance of the regular audio signal cables picking up noise or interference
from the power cords or digital cables. Using only high quality, shielded
cables will also help to prevent noise or interference from degrading the
sound quality of your system. If you have any questions see your authorized
Rotel dealer for advice about the best cable to use with your system.

The RR-DD91 Remote Control

Some functions can be done with either the front panel controls, or the
supplied RR-DD91 remote control. When these operations are described,
the square call out numbers refer to the main unit, while the encircled letters
refer to the remote control.

Remote Control Batteries

Two UM-4/AAA size batteries (supplied) must be installed before the remote
control can be used. To install the batteries, remove the cover on the back of
the RR-DD91. Install the batteries as shown in the illustration in the battery
well. Test the control for proper operation, then replace the cover. When
the batteries become weak the remote control won't operate the RDD‑1580
consistently. Installing fresh batteries should eliminate the problem.

AC Power and Control

AC Power Input

-
Your RDD-1580 is configured at the factory for the proper AC voltage in
the country where you purchased it, either 120 volts or 230 volts. The AC
line configuration is noted on a decal on the back panel.
RDD-1580 Digital to Analog Converter
NOTE: Should you move your unit to another country, it may be possible to
reconfigure it for use on a different line voltage. Do not attempt to perform
this conversion yourself. Opening the enclosure of the unit exposes you to
dangerous voltages. Consult a qualified service person or the Rotel factory
service department for information.
NOTE: Some products are intended for sale in more than one country and
as such are supplied with more than one AC cord. Please use only the cord
appropriate for your country/region.
The RDD-1580 should be plugged directly into a 2-pin polarized wall outlet
or into the switched outlet on another component in your audio system. Do
not use an extension cord.
Connect the supplied power cord to the Power Connector
the unit and the AC power outlet. The Standby indicator light is illuminated
if the unit is plugged in, it is in Standby mode.
If you are going to be away from home for an extended period of time such
as a month-long vacation, it is a sensible precaution to unplug the RDD-
1580 (as well as other audio and video components) while you are away.

Standby Switch and Indicator

Press the front panel Standby Switch button, to turn the unit on. One of the
input selector indicator light is illuminated when the unit is on. Press the
Standby Switch button again, the unit is in Standby mode.
When the Standby indicator is illuminated, the remote control ON and OFF
buttons may be used to activate the RDD-1580.
NOTE: Place the self adhesive ring over the light surrounding the Standby
switch if the blue light is too bright.
Remote Sensor
3
This remote sensor window receives IR commands from the remote control.
Please do not block this sensor.

Front Input Indicators

4
The front panel has a set of indicators showing which input is currently selected.
PC-USB : This is the rear USB connection
COAX 1 and 2: Set of Coaxial inputs 1 or 2
OPT 1 and 2: Set of Optical inputs 1 or 2
USB : This is the front USB connection.

Sampling Frequency Indicators

The Sampling Frequency light will illuminate if the music being played
matches one of the Sampling Frequency indicators.
NOTE: Not all supported Sampling Frequencies have an indicator. Your
music may still play even if it does not have a light associated with the
sample rate of your audio.
on the rear of
-
1
5