SOMFY Oximo WT Guia página 48

EN
2. 4. 2. Re-setting the end limits
1
8VH XQLYHUVDO DGMXVWLQJ FDEOH   IROORZ WKH LQVWUXFWLRQV LQ WKH FRUUHVSRQGLQJ
PDQXDO IRU FRQQHFWLRQ  RU XVH D QRQORFNLQJ GRXEOH SXVKEXWWRQ VZLWFK
7KH UHVHWWLQJ DQG DGMXVWPHQW RI WKH HQG OLPLWV GHSHQGV RQ WKH W\SH RI OLQNV DQG ORFNV XVHG
and whether or not there are stops on the end slat.
2. 4. 2. 1. With locks and with stops on the end slat
:KHQ WKH UROOHU VKXWWHU LV ¿WWHG ZLWK ORFNV DQG VWRSV RQ WKH HQG VODW WKH HQG OLPLWV DUH VHW
DXWRPDWLFDOO\ ,I QHFHVVDU\ UHVWRUH WKH GULYH WR LWV RULJLQDO FRQ¿JXUDWLRQ VHH VHFWLRQ HQWLWOHG
5HVWRULQJ WKH RULJLQDO FRQ¿JXUDWLRQ 
2. 4. 2. 2. With locks and without stops on the end slat
:KHQ WKH UROOHU VKXWWHU LV ¿WWHG ZLWK ORFNV DQG ZLWKRXW VWRSV RQ WKH HQG VODW WKH XSSHU HQG
OLPLW FDQ EH DGMXVWHG
Re-setting the upper end limit
,Q WKLV PRGH WKHUH LV D UHVSRQVH WLPH EHWZHHQ WKH
activation of the control point and the reaction by the
application.
Place the roller shutter at its upper end limit.
1)
3UHVV WKH 8S EXWWRQ IRU DSSUR[LPDWHO\  VHFRQGV
2)
Wait for 2 seconds.
3)
3UHVV WKH 8S EXWWRQ XQWLO WKH UROOHU VKXWWHU PRYHV
4)
EDFN DQG IRUWK
Repeat steps 3 and 4 four times.
5)
The last back and forth movement is brief.
‡
Place the roller shutter in the desired upper end
6)
limit position.
%ULHÀ\ SUHVV WKH 'RZQ EXWWRQ
7)
,I WKH UROOHU VKXWWHU UHDFWV UHSHDW VWHS 
Wait for 2 seconds.
8)
3UHVV WKH 'RZQ EXWWRQ XQWLO WKH UROOHU VKXWWHU PRYHV
EDFN DQG IRUWK
The new upper end limit position is programmed.
2. 4. 2. 3. :LWK ÀH[LEOH OLQNV DQG ZLWK VWRSV RQ WKH HQG VODW
:KHQ WKH UROOHU VKXWWHU LV ¿WWHG ZLWK ÀH[LEOH OLQNV DQG VWRSV RQ WKH HQG VODW WKH XSSHU HQG OLPLW
LV VHW DXWRPDWLFDOO\ ZKLOH WKH ORZHU HQG OLPLW FDQ EH DGMXVWHG
Re-setting the lower end limit
,Q WKLV PRGH WKHUH LV D UHVSRQVH WLPH EHWZHHQ WKH
activation of the control point and the reaction by the
application.
Place the roller shutter at its lower end limit.
1)
3UHVV WKH 'RZQ EXWWRQ IRU DSSUR[LPDWHO\  VHFRQGV
2)
Wait for 2 seconds.
3)
3UHVV WKH 'RZQ EXWWRQ XQWLO WKH UROOHU VKXWWHU PRYHV
4)
EDFN DQG IRUWK
Repeat steps 3 and 4 four times.
5)
The last back and forth movement is brief.
‡
Place the roller shutter in the desired lower end
6)
limit position.
%ULHÀ\ SUHVV WKH 8S EXWWRQ
7)
,I WKH UROOHU VKXWWHU UHDFWV UHSHDW VWHS 
Wait for 2 seconds.
8)
3UHVV WKH 8S EXWWRQ XQWLO WKH UROOHU VKXWWHU PRYHV
EDFN DQG IRUWK
The new lower end limit position is programmed.
46
Non contractual images
1)
4)
6)
8)
2 s
1)
4)
6)
8)
2 s
Copyright © 2005 - 2014 Somfy SAS. All rights reserved.
2) 3)
5 s
2 s
5)
[Step 3
+
Step 4]
[ 
7)
0.5 s
9)
2) 3)
5 s
2 s
5)
[Step 3
+
Step 4]
[ 
7)
0.5 s
9)