Troubleshooting Guide; Need Help - Good Earth Lighting SE1291-BP2-02LF0-G Manual De Instrucciones

ON ON
OFF OFF
2 Seconds
MANUAL OVERRIDE allows the light to turn on at any time, by overriding
all sensor controls, so the light comes on regardless of time of day.
Before doing any work on the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.
PROBLEM
Security light 1. Light switch is off.
does not come on
2. Fuse is blown/circuit breaker has tripped.
3. Fixture not properly wired to junction box.
4. It is daylight.
5. Motion sensor is pointed in the wrong direction.
6. Air temperature is about the same as a person's body
temperature and the (PIR) sensor cannot "see" the person.
Light continuosly 1. Light sensor is triggered by reflected light from the security
light itself.
cycles ON and OFF
(strobe effect). 2. Heat is being reflected from other sources and may be
triggering sensor on and off.
Light turns on during 1. Light may be installed in shadows/dark area.
daylight hours.
1. Sensor may be triggered by a small animal or passing car.
Light comes on for
no apparent reason.
2. Hot air (dryer vent, car exhaust, etc.) may be triggering
the sensor.
1. Motion sensor may be picking up a continuos flow of warm
Light stays on
air from an air vent, dryer vent or heat reflecting off a surface.
continuosly.
2. Interfence generated from transformers, fluorescent light
fixtures or electric motors are connected to the same circuit.
REPLACEMENT PARTS LIST: Hardware Kit: ZH-SE1291F02
Good Earth Lighting - 8 YEAR LIMITED WARRANTY: The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (8) years
®
from the date of original purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment.
We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge.
Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838
to obtain a return authorization number and an address where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any
case limited to replacement of the defective light fixture product. The manufacturer will not be liable for any other loss, damage, labor costs or injury which is caused by the product. This
limitation upon the liability of the manufacturer includes any loss, damage, labor costs or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature;
(III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty
gives you specific rights, and you may also have other rights which vary from state to state.
FCC STATEMENT: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has
been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that of the receiver. 4) Consult the dealer or
an experienced radio/TV technician for help.
FCC responsible party name : Good Earth Lighting, Inc. Address: 1400 E Business Center Drive, STE 108, Mount Prospect IL 60056, USA Telephone number: 1-800-291-8838

Need Help?

Good Earth Lighting 1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
®
Good Earth Lighting is a registered trademark of Good Earth Lighting, Inc. © 2020 Good Earth Lighting, Inc.
®
ON ON
OFF OFF

TROUBLESHOOTING GUIDE

POSSIBLE CAUSE
Please visit our website at: www.goodearthlighting.com/support or call the Customer Care Center
1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.
USING MANUAL OVERRIDE
SETTING THE LIGHT MANUAL OVERRIDE:
If the security light has been turned off at the switch, turn it on for 60 seconds to
allow the (PIR) sensor time to warm up prior to initiating the manual override
sequence.
To switch over to manual mode, switch the power OFF-ON-OFF-ON within 2
seconds.There are 2 ways to return to sensor control:
1) To immediately switch out of manual mode, repeat the manual mode sequence of
power OFF-ON-OFF-ON within 2 seconds. This will cancel out manual mode.
2) The security light will remain on until the internal dusk-to-dawn sensor detects
the next dusk-dawn cycle. Once light is detected, it will allow the motion sensor to
return to controlling the fixture the next day.
1. Turn light switch on.
2. Replace fuse/ turn the cicuit breaker back on.
3. Re-install light fixture.
4. Recheck at night.
5. Readjust motion sensor.
6. Decrease the SENSITIVITY control setting.
1. Change the position of the light head, aim light away from the reflecting
surfaces.
2. Decrease the SENSITIVITY control setting.
1. Light is operating as it was designed. Use manual override if necessary.
1. Decrease the SENSITIVITY control setting as necessary.
2. Increase the SENSITIVITY control setting as necessary.
1. Reposition the motion sensor.
2. Install the light on a circuit without transformers, fluorescent light fixtures
or electric motors connected to the circuit.
CORRECTIVE ACTION
Printed in Vietnam
3